Abstract:The trade-off between strength and ductility remains a significant challenge for high-entropy alloys (HEAs). The layer-by-layer printing manner inherent in the laser powder bed fusion (L-PBF) leads to distinctive microstructures in alloys, in turn yielding unexpected performances that are promising for resolving this contradiction. At present, the influence of L-PBF technology on the microstructures and mechanical properties of near-eutectic HEAs has yet to be explored. In the present work, a metastable AlCo 0.4 CrFeNi 2.7 hypoeutectic HEA with an extraordinary strength-ductility combination was successfully fabricated using L-PBF. The precipitation behaviors and mechanical properties of the alloy were further modulated through annealing. The results reveal that the high cooling rates inherent in L-PBF promote the formation of a "pseudoeutectic" structure featuring the face-centered-cubic (FCC) + body-centered-cubic (BCC) dual-phase nanolamellae. Furthermore, after annealing at 600-750 °C, the L1 2 and B2 precipitates are generated in the FCC lamellae, accompanied by a coarsening of the original Cr-rich precipitates (BCC) in the BCC lamellae. The as-printed sample exhibits remarkable mechanical properties, posing a yield strength of 1007 MPa, an ultimate strength of 1249 MPa, and a total elongation of ∼25.1%. After annealing at 750 °C, the tensile yield strength and ultimate strength are further increased to 1201 MPa and 1512 MPa, respectively, while the elongation is maintained at ~15.1%. The analysis results demonstrate that the high strength originates from the hard BCC lamellae and nanolamellar interfaces, while the good ductility stems from the soft FCC lamellae and coordinated deformation of the dual-phase nanolamellae. Furthermore, the strength increase is further substantiated through the introduction of annealing-induced nanoprecipitates, thereby contributing to additional precipitation strengthening.

Unique Strength-Ductility Balance of AlCoCrFeNi2.1 Eutectic High Entropy Alloy with Ultra-Fine Duplex Microstructure Prepared by Selective Laser Melting

High-strength AlCoCrFeNi2.1 eutectic high entropy alloy with ultrafine lamella structure via additive manufacturing

Selective laser melting of dense and crack-free AlCoCrFeNi<sub>2.1</sub> eutectic high entropy alloy: Synergizing strength and ductility

Microstructure and mechanical properties of high strength AlCoCrFeNi2.1 eutectic high entropy alloy prepared by selective laser melting (SLM)

Simultaneously Enhanced Strength-Ductility of AlCoCrFeNi2.1 Eutectic High-Entropy Alloy Via Additive Manufacturing

New insight into tailorable eutectic high entropy alloys with remarkable strength–ductility synergy and ample shaping freedom fabricated using laser powder bed fusion

Strength-ductility balance of AlCoCrFeNi 2.1 eutectic high-entropy alloy via additive manufacturing

High strength and ductility eutectic high entropy alloy with unique core-shell structure

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Microstructure and properties of AlCoCrFeNi 2.1 eutectic high entropy alloy manufactured by selective laser melting

Microstructural origins of high strength and high ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy

High-strength AlCoCrFeNi2.1 eutectic high entropy alloy skeleton with hollow brick wall structures by selective laser melting

High-strength Fe32Cr33Ni29Al3Ti3 fabricated by selective laser melting

Significant transitions of microstructure and mechanical properties in laser additive manufacturing AlCoCrFeNi 2.1 eutectic high-entropy alloy under heat treatment

Superior Strength-Ductility Synergy in Additively Manufactured CoCrFeNi High-Entropy Alloys with Multi-Scale Hierarchical Microstructure

High strength and ductility in a dual-phase hetero-structured AlCoCrFeNi2.1 eutectic high-entropy alloy by powder metallurgy

Microstructures and precipitation behaviors of a hypoeutectic high-entropy alloy prepared by laser powder bed fusion

Selective Laser Melting (SLM) Additively Manufactured CoCrFeNiMn High-Entropy Alloy: Process Optimization, Microscale Mechanical Mechanism, and High-Cycle Fatigue Behavior

Enhanced strength–ductility synergy in ultrafine-grained eutectic high-entropy alloys by inheriting microstructural lamellae

Processing Parameters, Microstructure and Properties of Al0.5CoCrFeNi High Entropy Alloy Prepared by Selective Laser Melting

In-situ synthesis of CoCrFeMnNi high-entropy alloy by selective laser melting