Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Re‐attainable Lubrication Films at 500°C Converted Through the Positional Polymerisation of DCDPS on the Preset Na2S Coating

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

The Thermal Stability and Lubricity of Zinc Thiomolybdenate at Temperatures Up to 500°C

Temperature-mediated Structural Evolution of Vapor–phase Deposited Cyclosiloxane Polymer Thin Films for Enhanced Mechanical Properties and Thermal Conductivity

The influence of polydiethylsiloxane (PDES) concentration on the tribolfilm of chlorophenyl silicone oil (CPSO) under high-temperature lubrication

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

An inorganic-organic hybrid CQDs@PVP lubricant additive: Achieving low friction and wear in PEG and water

High load capability, sticking scale inhabitation and promising lubrication of sodium carbonate coating for steel/steel contact at high temperature

High temperature solid/liquid lubrication behaviours of DLC films

Improved Tribological Performance of Polydopamine/Polytetrafluoroethylene Thin Coatings With Silica Nanoparticles Incorporated into the Polydopamine Underlayer

Ultralow Friction Polymer Composites Enabled by the Solid–liquid Core Microcapsules at High Temperatures

Designing a PAI/PTFE coating with enhanced high-temperature tribological properties by S8-POSS: Solid-liquid dual lubrication

Friction-Induced Clustered Rearrangement at a PbS Quantum Dot Nanocoating Via Long-Term Lubrication under an Atmosphere Environment.

High temperature lubrication performance of chlorophenyl silicone oil

Tribological performance of various metal-doped carbon dots as water-based lubricant additives and their potential application as additives of poly(ethylene glycol)

Improving the tribological performance of CFRPTFE at elevated temperature by sliding against Ti-TiCx/DLC film

Preparation and tribological properties of multi-layer graphene/silicon dioxide composites-based solid lubricant coatings at elevated temperatures

The Effect of Solid-Liquid Composite Lubrication on the Tribological Properties of Bearing Steel

Synergistic lubrication of Ag and Ag2MoO4 nanoparticles anchored in plasma-sprayed YSZ coatings: Remarkably-durable lubricating performance at 800 °C

Tribological Performance and Wear Mechanism of Compound Containing S, P, and B as EP/AW Additives in Copper Foil Oil

Synthesis of Polymer-Grafted Carbon Dots Serving as Multifunctional Lubricant Additives with Excellent Tribological Performance and Additional Rust Resistance Function for Steel/Steel Contact