Abstract:W-Ni alloy has been an important engineering material in military, nuclear industry and many other fields because of its excellent properties such as high strength and superior heat/corrosion/oxidation resistances. As a mainstream additive manufacturing technology based on powder-bed-fusion principle, selective laser melting (SLM) is suitable for the rapid fabrication of very complex W-Ni alloy components. However, researches on the powder densification behavior and microstructure formation mechanism of SLM W-Ni alloy are not thorough enough. In this work, a series of W-xNi (x = 16, 23, 30 wt.%) binary alloy samples were fabricated by SLM, using W/Ni mixed powders as the raw materials. The densification behaviors of the W/Ni mixed powders and the microstructure formation mechanisms of the different SLM W-Ni samples were studied. The results showed that when the W/Ni mixed powder bed was scanned by the laser, Ni powders with a relatively lower melting point would melt completely whereas W powders with a relatively higher melting point would rearrange themselves in the liquid Ni and only part of them could be dissolved into the liquid Ni. As the initial content of Ni powders increased, the rearrangement and dissolution of W powders proceed more sufficiently, thus leading to the improvement in densification degree. The relative densities of the W-16Ni, W-23Ni and W-30Ni SLM samples are 92.87 ± 0.67%, 98.66 ± 0.26% and 99.67 ± 0.18%, respectively. During the solidification processes of W-Ni molten pools, the precipitation of W grains from liquid Ni, the transformation of liquid Ni to γ-Ni solid solution and the precipitation of Ni2W from γ-Ni solid solution would occur in sequence. For the W-16Ni and W-23Ni samples, the grain morphology of the W precipitations is dendritic. For the W-30Ni samples, the W precipitations are globular. As a result of the unique melting- solidification behaviors, all the SLM samples possessed a tri-modal microstructure composed of unmelted W particles, dendritic/globular W grains, and γ-Ni solid solution with Ni2W intragranular precipitation. The average microhardness of the SLM W-Ni alloy samples decreased with the increase of Ni content, which could be explained by the variation in defect and microstructure features.

Influence of Selective Laser Melting Process Parameters on Microstructure and Properties of a Typical Ni-Based Superalloy

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Volume Energy Density on Selective Laser Melting Niti Shape Memory Alloys: Microstructural Evolution, Mechanical and Functional Properties

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Influence of Ni Contents on Microstructure and Mechanical Performance of AlSi10Mg Alloy by Selective Laser Melting

Microstructural Characteristics and Mechanical Properties of an Additively Manufactured Nickel-Based Superalloy

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Routine laparoscopic ultrasound can significantly reduce the need for selective intraoperative cholangiography during cholecystectomy

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Thermal behavior and microstructural evolution of additively manufactured Ni-based superalloys via multi-scale simulation

Research progress on selective laser melting processing for nickel-based superalloy

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

Effect of treatment mode on microstructure evolution and mechanical properties of nickel-based superalloy fabricated by selective laser melting

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

Microstructure and Tribological Behaviour of Inconel-625 Superalloy Produced by Selective Laser Melting

Effect of forming angle on the microstructure and properties of GH3536 nickel-based superalloy formed by SLM

Process Optimization of Selective Laser Melting Nickel-Based Superalloy

Powder densification behavior and microstructure formation mechanism of W-Ni alloy processed by selective laser melting

Selective laser melting of IN738 superalloy with a low Mn+Si content: Effect of energy input on characteristics of molten pool, metallurgical defects, microstructures and mechanical properties