Abstract:Single-pass isothermal hot compression tests on four medium-Mn steels with different C and Al contents were conducted using a Gleeble-3500 thermal simulation machine at varying deformation temperatures (900–1150 °C) and strain rates (0.01–5 s−1). Based on friction correction theory, the friction of the test stress–strain data was corrected. On this basis, the Arrhenius constitutive model of experimental steels considering Al content and strain compensation and hot processing maps of different experimental steels at a strain of 0.9 were established. Moreover, the effects of C and Al contents on constitutive model parameters and hot processing performance were analyzed. The results revealed that the increase in C content changed the trend of the thermal deformation activation energy Q with the true strain. The Q value of 2C7Mn3Al increased by about 50 KJ/mol compared with 7Mn3Al at a true strain greater than 0.4. In contrast, increasing the Al content from 0 to 1.14 wt.% decreased the activation energy of thermal deformation in the true strain range of 0.4–0.9. Continuing to increase to 3.30 wt.% increased the Q of 7Mn3Al over 7Mn by about 65 KJ/mol over the full strain range. In comparison, 7Mn1Al exhibited the best hot processing performance under the deformation temperature of 975–1125 °C and strain rate of 0.2–5 s−1. This is due to the addition of C element reduces the δ-ferrite volume fraction, which leads to the precipitation of κ-carbides and causes the formation of microcracks; an increase in Al content from 0 to 1.14 wt.% reduces the austenite stability and improves the hot workability, but a continued increase in the content up to 3.30 wt.% results in the emergence of δ-ferrite in the microstructure, which slows down the austenite DRX and not conducive to the hot processing performance.

Effects of Increasing the Strain Rate on Mechanical Twinning and Dynamic Strain Aging in Fe-12.5Mn-1.1C and Fe–24Mn-0.45C–2Al Austenitic Steels

Effect of Mn content and strain rate on mechanical properties of high-C high-Mn austenitic steel

Unusual grain-size effects on tensile deformation behavior of twinning-induced plasticity steel with low Mn content

Dynamic strain aging behavior of an advanced alumina-forming austenite stainless steel based on Fe-30Ni-15Cr-3.5Al

Influence of manganese on deformation behavior of lightweight steel at different strain rate

Dynamic strain ageing in an AlMg alloy at different strain rates and temperatures: Experiments and constitutive modelling

Influence of carbon addition on mechanical properties of Fe–Mn–C twinning-induced plasticity steels

Effect of Grain Size on the Plastic Deformation Behaviors of a Fe-18Mn-1.3Al-0.6C Austenitic Steel

Strain rate-dependent hardening with dislocation-twin interaction of Fe–Mn–Al–C steel using crystal plasticity

Influence of dynamic strain aging on low-cycle fatigue behavior in nano-sized κ-carbide strengthened FeMnAlC lightweight steel

Influence of strain rate on the tensile properties, misorientation distribution, and texture evolution of automotive-grade TRIP-assisted advanced high-strength steel

Tuning mechanical behavior and deformation mechanisms in high-manganese steels via carbon content modification

Revealing the Role of Pre-Strain on the Microstructure and Mechanical Properties of a High-Mn Austenitic Steel

Induction of deformation twinning by dynamic strain aging effect: Rate-temperature coupling effect and constitutive modeling

Dynamic Compressive Mechanical Behavior and Microstructure Evolution of Rolled Fe-28Mn-10Al-1.2C Low-density Steel

Effect of strain rate on microstructure and mechanical properties of spray-formed Al–Cu–Mg alloy

Intercritical annealing to achieve a positive strain-rate sensitivity of mechanical properties and suppression of macroscopic plastic instabilities in multi-phase medium-Mn steels

Effects of C and Al Alloying on Constitutive Model Parameters and Hot Deformation Behavior of Medium-Mn Steels

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Effects of Nitrogen Content and Strain Rate on the Tensile Behavior of High-Nitrogen and Nickel-Free Austenitic Stainless Steel

Temperature Dependence of Deformation Behaviors in High Manganese Austenitic Steel for Cryogenic Applications