Abstract:Growing usage of lightweight materials such as Al and Mg alloys in automotive body manufacture has come to a point that bonding of dissimilar materials is a realistic problem to address. A significant issue related to the bonding of dissimilar materials is that the differences in substrate surface conditions and substrate strengths often lead the bond to fail at strength far less than the bond strength established by adhesive manufacturer for a balanced joint. This research experimentally studied several factors potentially influencing initial strengths and debonding modes of adhesively-bonded Al-steel joints using single lap-shear coupons with comparison to like-substrate joints. Three commonly-used SLS coupon fabricating processes were investigated to determine which provided consistent bond strength and was efficient in making large quantities of coupons for the subsequent study. Next, the effect of prelube on the initial bond strength and debonding mode was investigated since the amount of prelube varies from sheet to sheet in automotive production. It was observed that even a very small change in the amount of prelube being applied on Al affected the initial bond strength. The more the prelube the weaker the bond became and the more adhesive failure occurred on the bonded Al surface. On the other hand, varying amount of the mill oil on the steel surface did not make much change to the bonding strength. Finally, various combinations of Al and steel substrates were studied to observe the effect of substrate materials on the initial bond strength and failure behavior. It revealed that the strength of joints between a relatively strong substrate and a relatively weak substrate fell below the strength of identical material joint made of the relatively strong substrate, and was closer to the strength of identical material joint made of the relatively weak substrate. For bonds having a high joint efficiency, adhesive failures were observed mostly on the surfaces of relatively weak substrates in the dissimilar material bonds due to large deformation in the weak substrate resulting in higher loading on that interface.

Adhesive Dynamic Behavior in the Clinch-Bonding Process of Aluminum Alloy A5052-H34 and Advanced High-Strength Steel JSC780

Mechanical Performance Evaluation of Multi-Point Clinch–Adhesive Joints of Aluminum Alloy A5052-H34 and High-Strength Steel JSC780

Steel-aluminum Plastic Clinching of an Inclined Wall Die

Dynamic Characteristics of Adhesive Bonded High Strength Steel Joints

Modelling of Deformation and Failure of Crash Toughened Adhesive Bonded Lap Shear Joints

Experimental Investigation On The Joining Of Aluminum Alloy Sheets Using Improved Clinching Process

Research on the joining of aluminum alloy and high-strength steel by dieless clinched-adhesive processes

Interfacial Bonding Behaviours of AA5052/DC05 in Synchronous Thermomechanical Joining-Forming Process

Mechanical characterization of a steel-aluminum clinched joint under impact loading

Experimental Investigation of the Mechanical Behavior of Aluminum Adhesive Joints under Mixed-Mode Loading Conditions

Modeling of High Strength Steel Joints Bonded with Toughened Adhesive for Vehicle Crash Simulations

Steel‐aluminum clinched joints mechanical properties and strength prediction under different geometric parameters

Effect Of Prelube, Surface Coating And Substrate Materials On Initial Strength Of Adhesive Joints Between Al Alloy And Steels

Center-Punching Mechanical Clinching Process for Aluminum Alloy and Ultra-High-Strength Steel Sheets

Effect of Base Steels on Mechanical Behavior of Adhesive Joints with Dissimilar Steel Substrates

Research on the Deformation Behaviors of the Clinch Joining of Aluminum Alloy and Quiet Steel Sheets

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Experimental Investigation of the Mechanical Reshaping Process for Joining Aluminum Alloy Sheets with Different Thicknesses

Interfacial Quality Prediction Model for Al/steel Sheets During Friction Stir–assisted Double-Sided Incremental Forming with Synchronous Bonding

Experimental Study of Initial Strengths and Hygrothermal Degradation of Adhesive Joints Between Thin Aluminum and Steel Substrates

Curing-Induced Distortion Mechanism in Adhesive Bonding of Aluminum Aa6061-T6 and Steels