Abstract:Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (Cf/C) composite for spark plasma sintering, two kinds of commercially pure α-Al2O3 powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (Tsg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al2O3 powder and 1400 °C for the 3 μm Al2O3 powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al2O3 compact can reach ∼80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.

Densification Mechanism of Os: Master Sintering Curve Fitting and Frist Principle Calculation

Study on the Densification of Osmium by Experiment and First Principle Calculations

Effect of osmium substitution on structural, electronic, mechanical, and thermodynamic properties of W–Os alloys: A first-principles study

Experimental and Molecular Dynamics Multiscale Study on Sintering and Interfacial Reaction of Fe2O3/CaO 2 O 3 /cao Particle System

Mechanical Stability and Thermodynamic Proper-Ties of Osc from First-Principles Calculations

Experimental and Molecular Dynamics Multiscale Study on Sintering and Interfacial Reaction of Fe2O3/CaO Particle System

Sintering Behavior and Activation Energy of Fe2O3 Nanoparticles: A Molecular Dynamics Research

Energetic, Mechanical, and Vibrational Stability of Metastable OsC Phase

A generalized master sintering curve based on nucleation-limited densification kinetics

Global Structure Search And Physical Properties Of Os2c

Modeling morphology evolution and densification during solid-state sintering via kinetic Monte Carlo simulation

Densification kinetics and sintering behaviour of a Ti(C0.7N0.3)-WC-Mo2C–NbC-(Co,Ni) compact

Enhanced magnetization of the highest- T C ferrimagnetic oxide Sr 2 CrOs O 6

Sintering behavior and activation energy calculation of nanoparticulate Fe3O4: a molecular dynamics simulation

First-principles study of structural and electronic properties of Al-Os intermetallic compounds

Preparation Of Nano-Structured 9cr-Ods Steel By Spark Plasma Sintering And Its Microstructure Characterization

Study and theoretical explanation on high-temperature strength of ODS-W alloy

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Tunable magnetic anisotropy of Os-Ru dimer on 2D transition metal chalcogenides substrates

Structural stabilities and natural half-metallic properties of OsXCoSi(X= Ti, Zr, Hf) quaternary Heusler alloys series first-principles calculations

Influence of the low interfacial density energy on the coarsening resistivity of the nano-oxide particles in Ti-added ODS material