Abstract:An intense texture is usually developed in conventional Mg alloys after deformation, resulting in unsatisfactory formability at room temperature. In the present work, a low-alloyed and weak-textured Mg-1.5Zn-0.2Ca (wt.%) alloy that exhibited an advantageous combination of strength and ductility was developed, with an ultimate strength of similar to 270 MPa and fracture elongation of similar to 30%. The role of Zn addition in the texture and microstructure evolution was systematically investigated. The Mg-xZn-0.2Ca (x = 0.5, 1.0, 1.5, and 2.0 wt%) alloys with increasing Zn content stored additional deformation energy, which accelerated the static recrystallization (SRX) process and resulted in a gradual weakening of the annealing texture. The co-addition of Zn and Ca contributed to the random SRX nucleation and the enhanced solute dragging effects by decreasing grain boundary energy, leading to a weaker texture in the Mg-1.5Zn-0.2Ca alloy than that in the Mg-1.5Zn and Mg-0.2Ca alloys after annealing. The excellent ductility of Mg-1.5Zn-0.2Ca alloy was attributed to the simultaneous increment of uniform elongation and post-uniform elongation as Zn content increases, benefited from its weakened texture and improved failure mode, respectively. This work provides valuable insights into the development of novel low-alloyed Mg sheets with a weak texture, which possess great potential for direct forming to near-net-shaped products without tearing and fracturing. (C) 2020 Elsevier B.V. All rights reserved.

Development of Corrosion-Resistant Mg-Al-Ca-Mn-Zn Alloy Sheet with Good Tensile Properties and Stretch Formability

Enhancing Mechanical Properties of Rolled Mg-Al-Ca-Mn Alloy Sheet by Zn Addition

A new magnesium sheet alloy with high tensile properties and room-temperature formability

Development of Weak-Textured and High-Performance Mg–Zn–Ca Alloy Sheets Based on Zn Content Optimization

Improving Formability of Mg–Ca–Zr Sheet Alloy by Microalloying of Zn

Microstructure, Mechanical, and Corrosion Properties of Extruded Low-Alloyed Mg-xZn-0.2Ca Alloys

Effect of Microalloyed Al and Ca on Mechanical Properties and Corrosion Resistance of High-Speed Extruded Mg-2Zn-1Mn (mass%) Alloy

Microstructure and Mechanical Property of High Strength Mg–Sn–Zn–Al Alloys

Role of Al Content on Tensile Properties and Stretch Formability of Mg-Al-Mn Alloy Sheet Produced by Continuous Hot-Rolling

Optimisation of Alloy Composition for Highly-Formable Magnesium Sheet

A Novel Mg-5Al-2Zn-2Sn Alloy with High Strength-Ductility Synergy Fabricated Via Simple Hot Rolling and Annealing Treatment

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Microstructures and Mechanical Properties of Mg–xAl–1Sn–0.3Mn (x = 1, 3, 5) Alloy Sheets

Towards development of a high-strength stainless Mg alloy with Al-assisted growth of passive film

Development of High Strength and Formability Mg-6Zn-0.2Ca Alloy Via Multi-Pass Warm Rolling and Aging Treatment

High-performance Magnesium Alloy with Multi-Element Synergistic Strengthening: Design, Microstructure, and Tensile Properties

High Ductility and Strong Work-Hardening Behavior of Zn Modified As-Hot-rolled Al-Mg Sheets

Individual Contribution of Zn and Ca on Age-Hardenability and Formability of Zn-Based Magnesium Alloy Sheet

Development of High-Strength, Low-Cost Wrought Mg–2.0 Mass% Zn Alloy with High Mn Content

Effects of Al and Zn Contents on the Microstructure and Mechanical Properties of Mg-Al-Zn-Ca Magnesium Alloys

Effects of Zn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg-2Al-0.5Ca Alloy