Abstract:Background: High-frequency ultrasonic transducer arrays are essential for high resolution imaging in clinical analysis and Non-Destructive Evaluation (NDE). However, the structure design and fabrication of the kerfed ultrasonic array is quite challenging when very high frequency (>= 100 MHz) is required.Objective and method: Here we investigate the effect of kerf depth on the performances of array transducers. A finite element tool, COMSOL, is employed to simulate the properties of acoustic field and to calculate the electrical properties of the arrays, including crosstalk effect and electrical impedance. Furthermore, Inductively Coupled Plasma (ICP) deep etching process is used to etch 36 degrees/Y-cut lithium niobate (LiNbO3) crystals and the limitation of etching aspect ratio is studied. Several arrays with different profiles are realized under optimized processes. At last, arrays with a pitch of 25 mu m and 40 mu m are fabricated and characterized by a network analyzer.Results: Kerf depth plays an important role in the performance of the transducer array. The crosstalk is proportional to kerf depth. When kerf depth is more than 13 mu m, the array with crosstalk less than -20 dB, which is acceptable for the real application, could provide a desired resolution. Compared to beam focusing, kerf depth exhibits more effect on the beam steering/focusing. The lateral pressure distribution is quantitatively summarized for four types of arrays with different kerf depth. The results of halfcut array are similar to those of the full-cut one in both cases of focusing and steering/focusing. The Full-Width-at-Half-Maximum (FWHM) is 55 mu m for the half-cut array, and is 42 mu m for the full-cut one. The 5-mu m-cut array, suffering from severe undesired lobes, demonstrates similar behaviors with the no-cut one. ICP process is used to etch the 36 degrees/Y-cut LiNbO3 film. The aspect ratio of etching profile increases with the kerf width decreasing till it stops by forming a V-shaped groove, and the positive tapered profile angle ranges between 62 degrees and 80 degrees. If the mask selectivity does not limit the process in terms of achievable depth, the aspect ratio is limited to values around 1.3. The measurement shows the electrical impedance and crosstalk are consistent with the numerical calculation.Conclusion: The numerical results indicate that half-cut array is a promising alternative for the fabrication of high-frequency ultrasonic linear arrays. In fact, the minimum pitch that could be obtained is around 25 mu m, equivalent to a pitch of 1.6 lambda, with a kerf depth of 16 mu m under the optimized ICP parameters. Crown Copyright (C) 2011 Published by Elsevier B. V. All rights reserved.

Optimization of a Random Linear Ultrasonic Therapeutic Array Based on a Genetic Algorithm.

Optimal Design of Random Sparse 2-D Arrays Based on Genetic Algorithm

An Improved Genetic Algorithm for Thinning Acoustic Array.

Sidelobe Suppression for a Steerable Parametric Source Using the Sparse Random Array Technique

A General Approach for Optimization of Ultrasonic Array Parameter and Setup Using Principal Component Regression

Synthesis of Unequally Spaced Array by Genetic Algorithm and Convex Optimization

Optical Phased Array with Low Grating Lobes Optimized by Using Hybrid Bat Algorithm

Research on improving lateral resolution of ultrasound phased array elements by using sparse matrix

Optimization Design of Sparse Arrays for Phased-Array 3D Imaging Sonar Systems

Extreme Sparse-Array Synthesis Via Iterative Convex Optimization and Simulated-Annealing Expanded Array

An efficient position optimization method based on improved genetic algorithm and machine learning for sparse array

A theoretical assessment of the relative performance of spherical phased arrays for ultrasound surgery

Optimization of Planar Thinned Antenna Array Based on Genetic and Convex Hybrid Algorithm

Optimized Design for Sparse Cross Arrays in Both Near-Field and Far-Field

Array Optimization for MIMO Radar by Genetic Algorithms

Hybrid Sparse Array Design Based on Pseudo-Random Algorithm and Convex Optimization with Wide Beam Steering

Synthesis of Extreme Sparse Array for Real-Time 3d Acoustic Imaging

Synthesis of Multibeam Sparse Circular-Arc Antenna Arrays Employing Refined Extended Alternating Convex Optimization

Optimization of hydrophone placement for acoustic arrays using simulated annealing

Design of an ultrasonic micro-array for near field sensing during retinal microsurgery

Numerical and Experimental Investigation of Kerf Depth Effect on High-Frequency Phased Array Transducer