Abstract:Absolute gravity measurement refers to the measurement of the absolute value of gravitational acceleration (g, approximately 9.8 m/s2). The precision of absolute gravity measurement is limited mainly by vibration noises. Vibration correction is a simple and feasible way to deal with vibration noises, which corrects the measurement results by detecting vibration noises with a sensor. At present, the vibration correction performance of different sensors lacks systematic analysis and evaluation. In this paper, the theoretical analysis of how the sensor characteristics affect the correction performance is carried out. The vibration correction performances of three sensors, two different seismometers and one accelerometer, are evaluated experimentally in the three cases with different vibration noises. The experimental results show that the correction precision obtained by using low-noise seismometer is limited mainly by its bandwidth and range. In case I i.e. the quiet environment, the standard deviation of corrected results obtained by using both seismometers can reach tens of μGal (1 μGal = 10–8 m/s2), which is close to that obtained by using an ultra-low-frequency vibration isolator. However, in case II i.e. the noisy environment, the standard deviation of corrected results obtained by both seismometers increase to hundreds of μGal due to the enhancement of high-frequency vibration components. This means that the correction performances of both seismometers deteriorate, and the performance of seismometer with narrower bandwidth turns even worse. Moreover, two seismometers cannot even work in case III with stronger vibration noises due to the range limitation. On the other hand, the correction precision obtained by using accelerometer is affected mainly by its resolution which is on the order of mGal (1mGal = 10–5 m/s2). Its bandwidth can reach hundreds of or even thousands of hertz and its range is generally over ±2 g, which is large enough to meet the needs for noisy and dynamic applications. In case I, the standard deviation after correction with accelerometer is larger than that before correction. This is because the intensity of vibration noises in this case is close to or even smaller than the self-noise of accelerometer so that it could not be detected effectively by accelerometer. In case II, the resolution of accelerometer is sufficient to detect the vibration noises effectively. The standard deviation of the results is reduced from 2822 μGal to 1374 μGal after correction with accelerometer, and equal to a precision of 0.1 mGal after 100 drops. In case III where the amplitude of vibration noise rises to 0.1 m/s2 and seismometer cannot work, the accelerometer could still achieve a precision of 0.3 mGal after 100 drops. The systematic deviation is corrected from –1158 mGal to –285 μGal and the standard deviation is reduced from 34 mGal to 3.3 mGal. Therefore, the low-noise seismometer is more suitable for vibration correction in a quiet environment with stable foundation, which could realize a standard deviation superior to hundreds of μGal, while the accelerometer is more appropriate for vibration correction in a complex or dynamic environment, which could achieve a standard deviation of mGal-level. Finally, the present results and analysis provide a theoretical guidance for selecting and designing the sensors in vibration correction applications.

Influence of magnetic field on the seismometer in vibration correction for atom gravimeters

The investigation of a μGal-level cold atom gravimeter for field applications

Rotation-induced Magnetic Field in a Coil Magnetometer Generated by Seismic Waves

Analysis and Processing of Vibration Interference Error of Oceanic Absolute Gravity Measurement Based on Variational Mode Decomposition

Vibration Compensation of an Atom Gravimeter

Continuous Gravity Measurement with a Portable Atom Gravimeter

Modulation of the Differential Phase in Atom Gravity Gradiometer Via a Bias Magnetic Field

Interference in Atomic Magnetometry

Impact of the Frequency Error of Direct Digital Synthesizers on the Evaluation of Two-Photon Light Shift in Atom Gravimeters

An improved magnetic properties measurement scheme using a torsion pendulum

Influence of Raman Laser Sidebands Effect on the Measurement Accuracy of Cold Atom Gravimeter

Correction of Vibration for Classical Free-Fall Gravimeters with Correlation-Analysis

Atomic gravimeter robust to environmental effects

Experiment on Dynamic Absolute Gravity Measurement Based on Cold Atom Gravimeter

Analysis of Vibration Correction Performance of Vibration Sensor for Absolute Gravity Measurement

A vibration correction method for free-fall absolute gravimeters

Effect of Magnetic Shielding on Levitation Characteristics of Superconducting Gravimeter

Demonstration of an ultrahigh-sensitivity atom-interferometry absolute gravimeter

Vibration Correction With Kalman Filtering Based Data Fusion for Absolute Gravimeters

Sensitive detection of local magnetic field changes with atomic interferometry by using superconducting Meissner effects

Accuracy Improvement of a Compact 85Rb Atom Gravimeter by Suppressing Laser Crosstalk and Light Shift