Abstract:It is irrefutable that the presence of hydrogen reduces the mechanical performance of many metals and alloys used for structural components. Several mechanisms of hydrogen-assisted cracking (HAC) of steels have been postulated. The direct evidence of the mechanisms by which hydrogen embrittles these materials has remained elusive. This is by virtue of our difficulty to directly observe the hydrogen distribution at spatial resolutions less than 100 nm and analysis volumes greater than 1 × 109 atoms at microstructural features such as grain boundaries, dislocations, twins, stacking faults and sub-micron inclusions that are all potential hydrogen trapping sites postulated to be responsible for the degradation of mechanical performance. Here, we report on an experimental methodology combining an elaborate fatigue testing protocol in an enriched gaseous deuterium environment with NanoSIMS (secondary ion mass spectrometry) imaging for detection of deuterium at spatial resolutions as low as 100 nm and accompanying TEM analysis. Type 316 stainless steel compact tension specimens were precharged in deuterium followed by fatigue testing at high stress ratio (0.7), low delta K (~11 MPa √m), and a frequency of 1 cycle per minute using a sawtooth waveform with a rise time of 30 s in high pressure (68.9 MPa) gaseous deuterium (99.999% purity) environment at room temperature. High resolution NanoSIMS imaging was then used to measure the deuterium distribution at the tip of and in the wake of secondary and tertiary fatigue cracks as well as at MnS inclusions. The use of deuterium eliminates the difficulties of interpreting hydrogen measurements by SIMS relating to the ubiquitous presence of hydrogen in all high vacuum systems and guarantees that deuterium measured by the NanoSIMS must be attributed to the fatigue testing protocol. This methodology has allowed us to directly observe the distribution of hydrogen in dislocation tangles ahead and in the wake of fatigue crack tips and at the interface of MnS inclusions. The protocol provides an avenue by which the path and speed with which hydrogen proceeds along its embrittling course of action may be directly followed through modifications of the fatigue testing parameters and/or alloy type and allows a means to validate at least qualitatively recently published models of enhanced hydrogen transport by dislocations.

In-situ 3D Observation of Hydrogen-Assisted Particle Damage Behavior in 7075 Al Alloy by Synchrotron X-ray Tomography

Surrogate Model-Based Assessment of Particle Damage Behaviour of Al-Zn-Mg Alloy

Analysis of Hydrogen-Assisted Brittle Fracture Using Phase-Field Damage Modelling Considering Hydrogen Enhanced Decohesion Mechanism

Hydrogen Induced Debonding of Mg<sub>2</sub>Si Particle / Aluminum Interface in Al-Mg-Si Alloy

Advancing the Hydrogen Tolerance of Ultrastrong Aluminum Alloys Via Nanoprecipitate Modification

OS0802-137 3D Image-Based Analysis of Damage Initiation and Microstructures in Aluminium Alloy

Assessment of hydrogen embrittlement behavior in Al-Zn-Mg alloy through multi-modal 3D image-based simulation

Hydrogen Embrittlement Prompt Fracture in Ni-based Single Crystal Superalloy

Effects of Hydrogen Charging and Deformation on Tensile Properties of a Multi-Component Alloy for Nuclear Applications

Hydrogen embrittlement revealed via novel in situ fracture experiments using notched micro-cantilever specimens

Ductile fracture via hydrogen pore mechanism in an aluminum alloy; quantitative microstructural analysis and image-based finite element analysis

High resolution NanoSIMS imaging of deuterium distributions in 316 stainless steel specimens after fatigue testing in high pressure deuterium environment

The in-situ TEM observation of microcrack nucleation in titanium aluminide

The hydrogen embrittlement mechanisms and hydrogen induced cracking process of selective laser-melted GH4169

Switching Nanoprecipitates to Resist Hydrogen Embrittlement in High-Strength Aluminum Alloys

Hydrogen-accelerated spontaneous microcracking in high-strength aluminium alloys

Hydrogen and deuterium charging of lifted-out specimens for atom probe tomography

Quantum Mechanical Modeling of Hydrogen Assisted Cracking in Aluminum

In Situ Investigation of Hydrogen Embrittlement Induced by Δ Phase in Selective Laser-Melted GH4169 Superalloy

Hydrogen trapping and embrittlement in high-strength Al-alloys

Quantitative Monitoring of the Environmental Hydrogen Embrittlement of Al-Zn-Mg-Based Aluminum Alloys via Dynamic Hydrogen Detection and Digital Image Correlation