Abstract:A solid oxide fuel cell (SOFC) stack requires metallic interconnects to electrically connect unit cells, while preventing fuel from mixing with oxidant. During SOFC operations, chromia scales continue to grow on the interconnect surfaces, resulting in a considerable increase of interfacial resistance, and at the same time, gaseous Cr species released from the chromia scales degrades the cathode performance. To address these problems, in this study, protective Mn2CuO4 coatings are fabricated on metallic interconnects (Crofer 22 APU) via a plasma spray (PS) process. The PS technique involves direct spray deposition of molten Mn2CuO4 onto the interconnect substrate and leads to the formation of high-density Mn2CuO4 coatings without the need for post-heat-treatment. The thickness, morphology, and porosity of the PS-Mn2CuO4 coating are found to depend on the processing parameters, including plasma arc power, gas flow rate, and substrate temperature. The PS-Mn2CuO4 coating fabricated with optimized parameters is completely impermeable to gases and has high adhesion strength on the interconnect substrate. Furthermore, no resistive chromia scales are formed at the coating/substrate interface during the PS process. As a result, the PS-Mn2CuO4-coated interconnects show a very low area-specific resistance below 10 mΩ cm2 at 800 °C in air and excellent stability during both continuous operation and repeated thermal cycling. This work suggests that an appropriate combination of the material and coating process provides a highly effective protective layer for SOFC interconnects.

Thermally Sprayed MCO/FeCr24 Interconnector with Improved Stability for Tubular Segmented-in-series SOFCs

Dense Mn1.5Co1.5O4 coatings with excellent long-term stability and electrical performance under the SOFC cathode environment

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Development and Application of HVOF Sprayed Spinel Protective Coating for SOFC Interconnects

Performance and In-Situ Densification of Mn-Co Spinel Coating on SUS430/441 Interconnect by Spraying Method

High Temperature Oxidation Behavior of SUS430 SOFC Interconnects with Mn-Co Spinel Coating in Air

Influence of Pre-Reduction on Microstructure Homogeneity and Electrical Properties of APS Mn1.5Co1.5O4 Coatings for SOFC Interconnects

Research on Fabrication and Property of NiMn2 O4 Coatings for Fe-Cr Alloy Interconnect Applications

Mn 1.4 Co 1.4 Cu 0.2 O 4 spinel protective coating on ferritic stainless steels for solid oxide fuel cell interconnect applications

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Mechanical reliability and life prediction of coated metallic interconnects within solid oxide fuel cells

Optimization of Plasma-Sprayed Lanthanum Chromite Interconnector Through Powder Design and Critical Process Parameters Control

Fabricating a MnCo coating to improve oxidation resistance and electrical conductivity of Crofer22H alloy as SOFC interconnect

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Performance Evaluation of a New Fe-Cr-Mn Alloy in the Reducing Atmosphere of Solid Oxide Fuel Cells