Abstract:Magnesium (Mg) is the lightest structural metal in the world. Therefore, Mg alloys hold great promise for weight-saving applications in the automotive and aerospace industries. However, the hexagonal close-packed (HCP) structure of Mg alloys results in limited dislocation plasticity and alternative deformation mechanisms such as deformation twinning that leads to poor formability and mechanical performance of Mg alloys. This inherent low ductility in Mg restricts its broad applicability as a high performance structural material. Further understanding of the fundamental deformation behavior in Mg and its alloys is therefore critical in order to identify potential processing routes that could enable high strength and ductility performance in Mg alloys. Dimensional refinement is regarded as an efficient way to tune the mechanical properties of materials. To probe the size-related mechanical properties of Mg and also the related fundamental deformation mechanisms, a series of in situ transmission electron microscopy nanocompression (TEM), nanotension and nanobending tests were conducted on single crystal and polycrystalline Mg with different crystallographic orientations. The external dimensions of the samples studied ranged from approximately 100 to 900 nm. The effect of crystal size was studied in regard to both deformation twinning behavior and dislocation behavior in single crystal Mg oriented for deformation twinning and basal slip, respectively. The influence of different grain boundary structures on the mechanical properties of polycrystalline Mg were also investigated using bicrystalline Mg specimens with constrained physical dimensions.For deformation twinning in Mg, it was found that there is strong crystal size effect. The formation of nanotwins was obtained in small specimens resulting in high strength (GPa level), high ductility and significant strain hardening, characteristics that have not been observed before in bulk materials. The nanotwinned structure is explained to be a result of the confined volume and large surface area in the small samples. The nucleation mechanism for deformation nanotwins was studied by computational simulations, and it was found that intrinsic nucleation of deformation twinning in Mg can be influence by the correlated nucleation of twinning dislocations, resulting in a nanotwinned structure. A strong size effect on the dislocation behavior in Mg was also discovered through the in situ TEM tests. Through systematic investigation three different size regimes were identified where the strength levels and dislocation plasticity were distinctly different. In the largest samples, three-dimensional dislocation plasticity was found; both the microstructure and the mechanical behavior were similar to those found in bulk. As the sample size decreased, two-dimensional dislocation plasticity became dominant, resulting in limited ductility and localized shear along the basal plane. Finally, in the extremely small samples (≤ 100 nm), multiple slip systems were activated under ultra-high stresses and exceptional ductility was reached. Corresponding high-resolution TEM (HRTEM) observations revealed a significant contribution from non-basal slip systems to the entire plastic deformation in these smallest samples. Presumably, the ultra-high stress decreased the anisotropy of the critical resolved shear stress (CRSS) between different slip systems, resulting in non-basal slip that generated a more homogenous deformation and much better ductility. The in situ TEM experiments were further compared to detailed molecular dynamic simulations. These observations of the reduction of CRSS anisotropy and ultra-high strength plasticity are discussed in light of future processing opportunities for high strength and high ductility structural materials. Lastly, the influence of different grain boundary structures on the deformation mechanisms and the mechanical properties of Mg at small scales was investigated by performing in situ SEM/TEM compression tests on polycrystalline Mg. Using electron backscatter diffraction (EBSD), it was observed that a low angle grain boundary served neither as an effective source of dislocation nucleation nor an effective barrier to mobile dislocations, resulting in localized shear. By comparison, high angle grain boundaries served as effective sources for dislocations and deformation twins, resulting in more stable and sustained plastic deformation. Taken together, the observations and analysis in this thesis give novel and powerful insight into the fundamental plasticity mechanisms in pure Mg. The experiments presented here are both rigorous and creative, generating insightful and powerful conclusions into Mg metallurgy with a high potential impact for light-weighting strategies in structural materials.

In-situ Deformation and the Size-Dependent Yielding Behaviour of Mg24Y5

Size-related Mechanical Properties of Pure Magnesium - Escholarship

An investigation of the combined size and rate effects on the mechanical responses of FCC metals

Orientation dependence of intracrystalline and grain boundary deformation behavior in Mg-2Y using nanoindentation and CPFEM

Uncovering the Inherent Size Dependence of Yield Strength and Failure Mechanism in Micron-Sized Metallic Glass

Relation Between Sample Size and Deformation Mechanism in Mg-Zn-Y 18R-LPSO Single Crystals

Deformation Behavior of Mg-Y-Ni Alloys Containing Different Volume Fraction of LPSO Phase During Tension and Compression Through In-Situ Synchrotron Diffraction

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

Ex-situ EBSD Analysis of Hot Deformation Behavior and Microstructural Evolution of Mg–1Al–6Y Alloy Via Uniaxial Compression

Plastic Strain Accommodation and Crack Initiation in a Randomly-Oriented Mg-8y-1zr Magnesium Alloy During Accumulated Tensile Deformation

Grain-scale deformation in a Mg−0.8 wt% Y alloy using crystal plasticity finite element method

Dislocation behavior in a polycrystalline Mg-Y alloy using multi-scale characterization and VPSC simulation

Emergence of external size effects in the bulk-scale polycrystal to small-scale single-crystal transition: A maximum in the strength and strain-rate sensitivity of multicrystalline Cu micropillars

Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility

In-situ Synchrotron Diffraction Study on Compressive Deformation Behavior of Mg92Y5Ni3 Alloy Mostly Composed of LPSO

Study of Slip Activity in a Mg-Y Alloy by in Situ High Energy X-ray Diffraction Microscopy and Elastic Viscoplastic Self-Consistent Modeling

In-situ Analysis of Slip Transfer and Heterogeneous Deformation in Tension of Mg-5.4Gd-1.8Y-1.5Zn Alloy

Dynamic Compression Behaviour and Constitutive Description of Fine-Grain Mg–4Zn–1Y Alloy

SIZE EFFECT ON DEFORMATION MODE IN MICRON-SIZED Ti-5Al SINGLE CRYSTAL LOADED ALONG $[2\,\overline 1 \,\overline 1 \,0]$ AND [0001]

In-Situ Study on the Tensile Deformation and Fracture Mechanism of a Bimodal-Structured Mg-Gd-Y Alloy

Effect of Yttrium Addition on the Hot Deformation Behaviors and Microstructure Development of Magnesium Alloy