Design of DTV Receiver Card Based on 2015VC-II CardBus Interface

Zheng Shi-bao

2005-01-01

Abstract:The paper introduces the 2015VC-II CardBus interface converter, and the DTV receiver solution based on this chip. The solution features smaller size, lower cost and good performance.

What problem does this paper attempt to address?

Digital Demodulator Design For Dvb-S2

Yang Jianxiao,Wang Kuang,Zou Zhiyong

2006-01-01

Abstract:This paper details on the design of DVB-S2 demodulator. The architecture of the demodulator compliant with the CCM (Constant Coding and Modulation) mode comprises timing recovery unit, frame synchronization unit, frequency recovery unit and frequency phase recovery unit. The system is easier to hardware implementation comparing with the system provided in [41 and [8]. After the key demodulation algorithms were discussed, a quantitative result is given, this allows us to draw conclusions concerning the achievable system performance under realistic complexity assumptions.
Implementing a DVB-T/H Receiver on a Software-Defined Radio Platform

Yong Jiang,Wen Xu,Cyprian Grassmann

DOI: https://doi.org/10.1155/2009/937848

2009-01-01

Abstract:Digital multimedia broadcasting is available in more and more countries with various forms. One of the most successful forms is Digital Video Broadcasting for Terrestrial (DVB-T), which has been deployed in most countries of the world for years. In order to bring the digital multimedia broadcasting services to battery-powered handheld receivers in a mobile environment, Digital Video Broadcasting for Handheld (DVB-H) has been formally adopted by ETSI. More advanced and complex digital multimedia broadcasting systems are under development, for example, the next generation of DVB-T, a.k.a. DVB-T2. Current commercial DVB-T/H receivers are usually built upon dedicated application-specific integrated circuits (ASICs). However, ASICs are not flexible for incoming evolved standards and less overall-area efficient since they cannot be efficiently reused and shared among different radio standards, when we integrate a DVB-T/H receiver into a mobile phone. This paper presents an example implementation of a DVB-T/H receiver on the prototype of Infineon Technologies' Software-Defined Radio (SDR) platform called MuSIC (Multiple SIMD Cores), which is a DSP-centered and accelerator-assisted architecture and aims at battery-powered mass-market handheld terminals.
An Implementation Scheme of Symbol-Processing in DVB-S Receiver

YI Zhi-qiang,Huang Zhi-jie,WANG Kuang

DOI: https://doi.org/10.3969/j.issn.1001-7119.2005.04.019

2005-01-01

Abstract:This paper proposes an implementation scheme of symbol-processing in DVB-S receiver. By using Secondary Encode and special sync-searching byte-recovering circuits, not only the processing time reduces remarkably, but also needs less hardware resource. This scheme has already been applied in the chip design of satellite digital television.
Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

ZHANG Jin,XU Yuan-xin,ZHANG Ji,WANG Kuang

DOI: https://doi.org/10.3969/j.issn.1671-7147.2005.03.003

2005-01-01

Abstract:The paper describes a DVB based HDTV audio decoder used in multi-channel extension and presents an improved algorithm for the synthesis filter bank. It is found that when the symmetry of coefficient and the similarity of the allocation tables, computational amount and memory size are reduced by more than 50%. DSP/BIOS operating system simplifies developing various DSP systems. This decoder can also be used in Digital Audio Broadcasting systems.
DVB-S2 Inner Receiver Design for Broadcasting Mode

Yang Jian-xiao,Wang Kuang,Zou Zhi-yong

DOI: https://doi.org/10.1631/jzus.2007.a0028

2006-01-01

Journal of Zhejiang University SCIENCE A

Abstract:This paper details on the design of DVB-S2 receivers which is compliant with the broadcasting mode. Special attention is paid to the specific receiver functions necessary to demodulate the received signal. To show the system performance we consider the design of a complete receiver consisting of timing recovery unit, frame synchronization unit, frequency recovery unit and phase recovery unit. The system is easier to hardware implementation comparing with that provided in (ETSI, 2005; Sun et al. , 2004). After the performance of the algorithms is analyzed and a quantitative result is given, this allows us to draw conclusions concerning the achievable system performance under realistic complexity assumptions.
Design of Infrared Business Card Exchanger Chip

CHEN Ming,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1001-9146.2006.05.014

2006-01-01

Abstract:This paper introduces the design of a special business card management chip,which adopts point-to-point infrared wireless data communication technology.The new chip can improve the efficiency of business cards management,improve the security and quality of the infrared communication,and simplifies the operation.The chip has been taped out(using a 5V 0.6um CMOS mix-signal double well,double poly,double metal technology) and tested.
The Design and Implementation of a DVB Receiving Chip with PCI Interface

Xu Ningyi,Li Shaohua,Yu Wei,He Guanghui,Zhang Hao,Luo Fei,Zhou Zucheng

DOI: https://doi.org/10.1145/1120725.1120893

2005-01-01

Abstract:A DVB receiving chip with PCI interface for PC is presented. The chip supports DVB protocols and integrates useful interfaces, including I 2 C, SmartCard and PCI. A card with this chip could change PC into digital TV terminal. The architecture of FPGA prototype system together with some main design issues is introduced. The experimental result shows that the chip could accomplish required functionalities.
A new VLSI design for Viterbi decoder based on ASIP

Zhiqiang Yi,Yuanxin Xu,Yun Li,Kuang Wang

DOI: https://doi.org/10.1109/ICCCAS.2002.1179065

2002-01-01

Abstract:Trellis Code Modulation (TCM) has been widely used because it can obtain 2.55∼7.37 dB coding gain without bandwidth expansion or reduction of the effective information rates. Since Viterbi decoder plays an important role in the realization of HDTV system, we conduct the research and development on integration of Viterbi decoder. This paper proposes a new VLSI design of Viterbi decoder using ASIPs based on hardware/software co-design idea. It reduces the total design time and enhances the reliability of VLSI. We have successfully used this method for the design of Viterbi decoder in the ASTC-HDTV receiver chip.
Design Of Portable Infrared Business Card Exchange System On Chip

Y Han,Mw Shi,Hy Du

2004-01-01

Abstract:To be different from the universal asynchronous design in multichip, a new-style design of the synchronous system on monolithic chip is presented to apply to exchange and management of business cards in this paper. Every part is accomplished and some improvement is made in the circuits to decrease power consumption. In addition, we adopt SOC (System on Chip) design to reduce fabrication and system test costs, introduce a controllable high-speed infrared driver to enhance the security and quality of communication, and design reduced instruction set to enhance the quality and efficiency of business cards management and depress systematic redundancy. This chip is fabricated in 0.6um mixed-signal CMOS process (double poly, double metal). packaged as well as tested primarily.
Design of DVB-C Mapping Circuit

包莉娜,梁坚,易志强,王匡

DOI: https://doi.org/10.3969/j.issn.1000-0755.2003.08.006

2003-01-01

Abstract:This paper focuses on the principles and method of mapping circuit in digital cable television(DVB-C),DVB-C System and implementation in ASIC(Applicatio n Specific Integrated Circuits)of DVB-C channel receiver.
Physical Layer Design For Dvb-S2 Ccm Mode

Yang Jianxiao,Wang Kuang,Zou Zhiyong

DOI: https://doi.org/10.1109/ISPACS.2006.364809

2006-01-01

Abstract:This paper details on the design of DVB-S2 receivers which is compliant with the constant coding and modulation (CCM) mode. Special attention is paid to the specific receiver functions necessary to demodulate the received signal. To show the system performance we consider the design of a complete receiver consisting of timing recovery unit, frame synchronization unit, frequency recovery unit, frequency phase recovery unit and a digital automatic gain controller. The system is easier to hardware implementation comparing with the system provided in [4] and [8]. After the performance of the algorithms is analyzed and a quantitative result is given, this allows us to draw conclusions concerning the achievable system performance under realistic complexity assumptions.
Design and implementation of twin transport stream demultiplexor in HDTV decoder

Zhu Zheng,Zhu Mengyao,Wang Lianghao,Luo Kai,Huang Zhijie,Ming Zhang

DOI: https://doi.org/10.1109/ICASIC.2007.4415734

2007-01-01

Abstract:A new architecture for transport stream demultiplexer (TS Demux) in high definition television (HDTV) decoder is presented in this paper, which is able to demultiplex two TS inputs synchronously. We have pursued a hardware-based design that controlled by the software to yield high performance in the least silicon area. The key parts of the architecture, including PID filter, section filter and Memory Control Unit (MCU), are shared by the two TS inputs in terms of a time slice. Owing to the elaborate shared mechanism, our design is efficient to support more tremendous functions with less resource compared to the current scheme.
Design and Implementation of SI Module in Digital TV STB

谷志奇,余松煜

DOI: https://doi.org/10.3969/j.issn.1002-8692.2004.03.016

2004-01-01

Abstract:This paper presents an optimized scheme for DVB-SI receiving module, in which the SI database is combined with the section filter. Consequently, the module structure is compact and the efficiency is high.
Design and Implementation of DVB-C Receiver Application on Windows Platform

ZUO Yi,YU Hongyang,ZHANG Ping

DOI: https://doi.org/10.3969/j.issn.1002-8692.2012.10.011

2012-01-01

Abstract:The framework of DirectShow and BDA which is needed to receive DTV signals on Windows platform is simply analyzed in this paper.Meanwhile,the design of PC receiver application for DVB-C is discussed and its complete implementation process is also given.The test results show that PC receiver can accurately analyze the information of multiplexed TS stream and fluently play audio and video streams.
Design and Realization of Network Interface Module of DTV

ZHA Bing,ZHU Xiao-dong,WANG Jin-lin,NI Hong

DOI: https://doi.org/10.3969/j.issn.1002-8692.2006.05.010

2006-01-01

Abstract:In this paper, we introduce a new structure of design and realization of the Networking Interface Module of DTV. This solution unifies the hardware and software interface of NIM module, so the hardware module can be changed to any type provided by the designer, without reloading the software. This common interface brings more agility to the manufactures and can reduce the periods of the project.
A Single Receiving Chip for DVB Data Broadcasting System

Guanghui He,Ningyi Xu,Wei Yu,Zucheng Zhou

DOI: https://doi.org/10.1109/tce.2006.1706511

2006-01-01

IEEE Transactions on Consumer Electronics

Abstract:In this paper, we present a single-chip receiver for DVB data broadcasting system, which is designed using the methodology of hardware and software co-design. The hardware part filters out and descrambles the necessary MPEG-2 transport stream (TS) packets, then sends them to PC. Some useful peripheral functions such as PCI interface, I 2 C bus controller and smart card 7816 interface are also developed to provide a cost-effective solution. Meanwhile, multi-protocol decapsulation related to data broadcasting protocol is analyzed and implemented mainly by software. In order to improve the throughput and hardware utilization, we adopt chaining mode direct memory access (DMA) scheme and a double buffer approach both in hardware and in software. Moreover, the parameters of chaining mode DMA and the depth of buffer are further optimized by theoretical analysis. The result indicates the throughput of chaining mode DMA is up to 475.8 Mb/s, which is 24 times as much as non-chaining mode DMA strategy
The Multifunctional Card of DTV Receiver Based on Wireless Network and PCMCIA Interface

但唐仁,刘岩

DOI: https://doi.org/10.3969/j.issn.1672-6332.2008.04.013

2008-01-01

Abstract:The paper introduces a kind of DTV receiver card which combines the technology of the terrestrial DTV channel demodulator,DTV demux and decoder,GMS/CDMA communication,portable reception design and PCMCIA interface.Associating the specialty of mobile telephone and wide band reception of terrestrial DTV,the function of bi-directional wireless alternant is achieved on the notebook PC.
Bus Design for HDTV SoC Decoder

李东晓,姚庆栋,刘鹏,周莉

DOI: https://doi.org/10.3969/j.issn.1007-0249.2003.03.018

2003-01-01

Abstract:Bus design methodology for the HDTV system-on-a-chip (SoC) decoder is presented. Time sliced arbitration scheme, incorporated with synchronization control of HDTV decoding, is employed in the bus design process. The bus data transmissions are scheduled elaborately to cooperate with the HDTV decoding process. The objective of proposed bus design approach is to utilize the bus bandwidth efficiently and reduce the amount of internal data buffers sufficiently. Following this approach, hardware cost can be reduced while the required real time performance is assured.
ASIC Design of DVB Transport Stream Receiving Chip

Guanghui HE,Wei YU,Xingbo ZHAO,Zucheng ZHOU

DOI: https://doi.org/10.3321/j.issn:1000-0054.2007.01.015

2007-01-01

Abstract:In order to receive digital video broadcasting(DVB) program with computer,this paper presents an application specific integrated circuits(ASIC) design of DVB transport stream receiving chip based on PCI interface.Hardware-software partitioning strategy is based on real-time requirement and complexity profiles of DVB system.Data path architecture is focused on the design of high-speed channel to improve the bandwidth.Furthermore,the parameters of chaining mode direct memory access(DMA) and the depth of buffer are optimized by theory analysis.The result indicates the bandwidth of chaining mode DMA is up to 476.6 Mb/s,which is 25 times as much as original DMA strategy.The chip can enhance the ability of receiving data and has been fabricated in 0.35 μm CMOS process of Fujitsu.

Design of DTV Receiver Card Based on 2015VC-II CardBus Interface

Digital Demodulator Design For Dvb-S2

Implementing a DVB-T/H Receiver on a Software-Defined Radio Platform

An Implementation Scheme of Symbol-Processing in DVB-S Receiver

Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

DVB-S2 Inner Receiver Design for Broadcasting Mode

Design of Infrared Business Card Exchanger Chip

The Design and Implementation of a DVB Receiving Chip with PCI Interface

A new VLSI design for Viterbi decoder based on ASIP

Design Of Portable Infrared Business Card Exchange System On Chip

Design of DVB-C Mapping Circuit

Physical Layer Design For Dvb-S2 Ccm Mode

Design and implementation of twin transport stream demultiplexor in HDTV decoder

Design and Implementation of SI Module in Digital TV STB

Design and Implementation of DVB-C Receiver Application on Windows Platform

Design and Realization of Network Interface Module of DTV

A Single Receiving Chip for DVB Data Broadcasting System

The Multifunctional Card of DTV Receiver Based on Wireless Network and PCMCIA Interface

Bus Design for HDTV SoC Decoder

ASIC Design of DVB Transport Stream Receiving Chip