Abstract:Obtaining high strength without sacrificing ductility in Mg alloys is of great importance. However, the hexagonal close-packed crystal structure critically limits the deformation of Mg alloys. In this work, novel Mg-1.5Zn-0.5Zr-0.5Sr (wt.%) alloys were fabricated through homogenization, direct extrusion (DE), and extrusion-shearing (ES) processes. The effects of three different processes on microstructures, texture, and mechanical properties were thoroughly investigated. The results show that the average grain size of the alloy was greatly refined after hot extrusion. The alloy after the DE process exhibited a typical bimodal microstructure with dynamic recrystallized (DRXed) grains showing a strong < 101 ̄0 > fiber texture parallel to extrusion direction (ED), while the small-sized unDRXed grains showed relatively weak basal texture. In addition, the strength was significantly improved, with the value of yield strength (YS) reaching ∼229 MPa and ultimate tensile strength (UTS) reaching ∼262 MPa. This is mainly attributed to grain boundary strengthening and dislocation strengthening. Compared to the DE-processed alloy, the basal texture intensity was significantly decreased and non-basal slip was activated after the ES process, which indicates that the shearing deformation during ES could improve the ductility, with the fracture elongation (FE) increased from ∼13.9 % to ∼21.4 %. This work aims to unveil the deformation mechanisms in Mg-1.5Zn-0.5Zr-0.5Sr alloy and provides an efficient way for preparing micro-alloying Mg alloys with low cost and significant improvement of comprehensive properties.

Microstructure, Mechanical and Corrosion Properties of Ultrafine-Grained Mg-2%Sr Alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructural Assessment, Mechanical and Corrosion Properties of a Mg-Sr Alloy Processed by Combined Severe Plastic Deformation

Research on Microstructures and Mechanical Properties of Mg-Gd-Y-Sr-Zr Alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Y Alloy

Influence of Heat Treatment on the Evolution of Microstructure and Mechanical Properties of Mg-7Gd-5Y-0.6Zn-0.8Zr Magnesium Alloy

Influence of Heat Treatment on Microstructure and Mechanical Properties of Mg-10gd-3y-1.2zn-0.4zr Alloy

Microstructure and Mechanical Properties of a Mg-Zn-Y-Zr Alloy Processed by Thermo-Mechanical Treatment

Influence of Heat Treatment on Microstructures and Mechanical Properties of Gravity Cast Mg–4.2Zn–1.5RE–0.7Zr Magnesium Alloy

Microstructures and Mechanical Properties of Extruded Mg-9Gd-4Y-0.6Zr-T5 at Elevated Temperatures

Microstructure Evolution and Deformation Behavior of Extruded Mg-5Al-0.6Sc Alloy during Room and Elevated Temperature Tension Revealed by Ex-Situ EBSD and VPSC

Effect of Strontium on the Microstructure, Mechanical Properties, and Fracture Behavior of AZ31 Magnesium Alloy

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Mechanical Properties and Microstructure of Az31 Magnesium Alloy Tubes

Microstructure and Strengthening Mechanism of a Thermomechanically Treated Mg–10Gd–3Y–1Sn–0.5Zr Alloy

Effect of thermal treatment on the bio-corrosion and mechanical properties of ultrafine-grained ZK60 magnesium alloy

Effect of Heat Treatment on Microstructure and Properties of Mg-12Y-1Al Alloy

Effect of heat treatment on microstructure and mechanical properties of Mg-4Y-1.6Nd-1Sm-0.5Zr alloy

Effect of Thermo-Mechanical Treatment on the Microstructure and Mechanical Properties of a Mg–6Gd–2Nd–0.5Zr Alloy