Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Microstructure and Mechanical Properties of Ti6Al4V/Inconel718 Functionally Graded Materials by Directed Laser Deposition

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Compositional Changes and Microstructure Evolution of Ti6Al4V-Inconel718 Functionally Graded Materials by Laser Additive Manufacturing

Microstructure and mechanical properties of Ti60–Ti 2 AlNb functionally graded materials fabricated by laser directed energy deposition

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

Intermetallic Phases Transition Mechanism of the Interface of Ti6Al4V-Inconel718 Graded Material by Laser Additive Manufacturing

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Microstructure Evaluation and Mechanical Properties of Ti6Al4V/Inconel 718 Composites Prepared by Direct Laser Deposition

Effect of TiC Content on Mechanical Properties and Microstructure Evolution of TiC/Inconel 718 Functionally Gradient Materials by Direct Energy Deposition

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Microstructure evolution and high temperature resistance of Ti6Al4V/Inconel625 gradient coating fabricated by laser melting deposition

Microstructure and Mechanical Properties of Directed Energy Deposited 316l/ti6al4v Functionally Graded Materials Via Constant/gradient Power

Laser Rapid Manufacturing of Stainless Steel 316l/inconel718 Functionally Graded Materials: Microstructure Evolution and Mechanical Properties

Microstructure and Mechanical Property of Laser Melting Deposition (lmd) Ti/Tial Structural Gradient Material

Development and Characterization of 316l/inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition

Microstructure and Hardness of S304/Ni25/Tc4 Functionally Graded Materials Fabricated by Laser Solid Forming

Functionally Graded Alloys from 316 Stainless Steel to Inconel 718 by Powder-Based Laser Direct Energy Deposition

Functionally Graded Material Fabricated by Powder-based Laser Directed Energy Deposition: From Conventional to Complex Concentrated Alloys

Effect of heat treatment on microstructures and mechanical properties of Inconel 718 additively manufactured using gradient laser power

Microstructure-property Correlations in As-Built and Heat-Treated Compositionally Graded Stainless Steel 316L-Inconel 718 Alloy Fabricated by Laser Powder Bed Fusion

Microstructure evolution and mechanical properties of TiB/Ti6Al4V gradient-material lattice structure fabricated by laser powder bed fusion