Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Experimental and Numerical Investigation of Transcritical Mixing under Multi-Component Gas Conditions

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

An Evaluation of Gas-Phase Micro-Mixing Models with Differential Mixing Timescales in Transported PDF Simulations of Sooting Flame DNS

Phase Transitions of Multi-Component Fuel Droplets under Sub- and Supercritical Conditions

Atomic-level insights into transition mechanism of dominant mixing modes of multi-component fuel droplets: From evaporation to diffusion

Evaluation of Trans-Critical Transition of Single- and Multi-Component Sprays under Diesel Engine-Like Conditions

On the transition between two-phase and single-phase interface dynamics in multicomponent fluids at supercritical pressures

Modeling of Supercritical-Pressure Turbulent Combustion of Hydrocarbon Fuels Using A Modified Flamelet-Progress-Variable Approach

Experimental Study of Injection Characteristics under Diesel’s Sub/trans/supercritical Conditions with Various Nozzle Diameters and Injection Pressures

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

A molecular dynamics study of evaporation of multicomponent stationary and moving fuel droplets in multicomponent ambient gases under supercritical conditions

Computational Modeling and Analysis of Diesel-fuel Injection and Autoignition at Transcritical Conditions

Transcritical Mixing and Auto-Ignition of n-dodecane Liquid Fuel using a Diffused Interface Method

Liquid fuel evaporation under supercritical conditions

Modeling and Simulation of Diesel Injection at Transcritical Conditions

Surface tension and evaporation behavior of liquid fuel droplets at transcritical conditions: Towards bridging the gap between molecular dynamics and continuum simulations

Microscopic investigation and local standard deviation analysis of liquid propane jets in supercritical environment

Experimental Study on Spray and Atomization Characteristics under Subcritical, Transcritical and Supercritical Conditions of Marine Diesel Engine

Numerical simulation of trans-/near-/supercritical injection characteristics based on real fluid properties

Experimental and Numerical Study of the Pollution Formation in a Diesel/cng Dual Fuel Engine

Analysis and Experiments about the Characteristics of Mixing Process in the Premixed Gas Turbine