Abstract:We have witnessed a transit of seismic tomography from ray-based traveltime inversion to wave equation-based waveform inversion during the past two decades. As is widely known, full waveform inversion outperforms traveltime tomography in resolving velocity variations with dimensions comparable and smaller than the dominant wavelength. However, this may not be always true in real practice, mainly due to the presence of unknown data noise, the lack of accurate initial models for the iterative inversion process (including material properties and source mechanisms), and the high demand for computational resources. Further efforts are required to develop techniques for using full waveform contents in seismic imaging studies, especially for the use of high-frequency waveform data (>1 Hz on regional scales). We have attempted to use common-source double-difference traveltime data in wave equation-based adjoint tomography studies of subsurface structures beneath Northeast Japan and Alaska. Because of the high level of waveform similarity, reliable common-source double-difference traveltime data at neighboring seismic stations are measured via cross-correlation approach. Insightful results are obtained. However, it is still computationally prohibitive to model high-frequency data by solving 3-D wave equations, limiting the resolution of seismic images. We admit that there is still a long way to go for the possible wide application of high-frequency full waveform inversion.Traveltime is the most reliable information that can be extracted from raw seismological recordings. We have developed a new modality of seismic imaging, called adjoint-state traveltime tomography, to unleash the full potential of traveltime in imaging subsurface structures. To avoid potential failure of ray tracing in 3D complex media, isotropic eikonal equation and anisotropic eikonal equations are used to model seismic traveltime field in heterogenous and anisotropic media, and the associated inverse problems are solved by the efficient adjoint state method. No ray tracing is required for the novel adjoint-state traveltime tomography method. Importantly, the sensitivities of traveltime-related objective functions to material parameters can be accurately measured even in complex media. We view adjoint-state traveltime tomography as a new framework for seismic tomography, as it naturally implements various body wave and surface wave tomographic inversions in a very similar way. Good performances of the adjoint-state traveltime tomography method will be reported via various case studies in regions with typically different tectonic settings. It is worth noting that an accompanying software package, TomoATT, is under development.

Automatic Traveltime Picking Using Structure-Enhanced High-Dimensional Time-Frequency Transform

Highly efficient methods of seismic data acquisition based on sparse constraints and blended-source excitation

The Comparison of Time-frequency Analysis Methods and Their Applications

Study on highly efficient seismic data acquisition method and theory based on sparsity constraint

Automatic Time Picking for Weak Seismic Phase in the Strong Noise and Interference Environment: An Hybrid Method Based on Array Similarity

4D Seismic Travel Time Tomography for Detecting Temporal Velocity Changes

Automatic Microseismic Event Detection and Arrival Picking Based on Waveform Cross-Correlation

Automatic First-Arrival Pickingmethod Via Intelligent Markov Optimal Decision Processes

Elastic Wave Equation Traveltime Inversion With Dynamic Time Warping Based on High-Speed Train Seismic Data

A travel-time tomography method for improving horizontal resolution of high-frequency surface-wave exploration

Adjoint-state traveltime tomography: A new modality of seismic imaging

High-Dimensional Constrained Fuzzy C-Means (HCFCM) Algorithms for Automatic First-Arrival Picking

Double-Difference Tomography with a Deep Learning–Based Phase Arrival Weighting Scheme and Its Application to the Anninghe–Xiaojiang Fault Zone

Automatic Traveltime Inversion Via Sparse Decomposition of Seismic Data

Time-Reassigning Transform for the Time–Frequency Analysis of Seismic Data

Automatic Horizon Picking Using Multiple Seismic Attributes and Markov Decision Process

Using high-precision travel time extraction to detect time deviation of seismic instruments

Seismic Time-frequency Analysis Using Improved Complete Ensemble Empirical Mode Decomposition

Time-lapse Image Registration by High-Resolution Time-Shift Scan

Adaptive and Automatic P-and S-phase Pickers Based on Frequency Spectrum Variation of Sliding Time Windows

An Iterative Kalman Filter-based Method for Traveltime Tomography