Abstract:A new jet fuel surrogate was developed in this work by emulating real jet fuel properties including physical, gas phase chemical properties and threshold sooting index (TSI). An intelligent optimization methodology was proposed to calculate the species composition that inherently satisfies both the physical and chemical characteristics as well as sooting tendency. Eight properties were selected as the target properties for the jet fuel surrogate development, including liquid density, viscosity, surface tension, cetane number (CN), hydrogen carbon (H/C) ratio, molecular weight (MW), lower heating value (LHV) and TSI. As a result, the CN, H/C ratio, LHV, TSI and density of the new jet fuel surrogate are reproduced excellently with very little deviations within 3%. The averaged deviation of viscosity is −6.318% and the deviations of MW is 9.776%. As the highest deviation among all properties, the averaged deviation of surface tension is 11.76%. Based on the newly developed jet fuel surrogate, a skeletal jet fuel surrogate mechanism with 5 components including decalin, n-dodecane, iso-cetane, iso-octane and toluene was developed. The skeletal jet fuel surrogate mechanism was significantly compacted into 74 species and 189 reactions by describing the chemistries for the oxidation of large molecules C4–Cn and small H2/CO/C1 molecules respectively, which makes it practical to be used for 3-D engine combustion simulations. The validations of ignition delay times present reasonable agreement between experiment and predictions over a wide range of equivalence ratios (0.5–2.0) and pressures (8–30 atm), except for a shift of negative temperature coefficient (NTC) region towards higher temperatures at Φ = 1.5, 20 atm: in the simulation the NTC region is from 830 K to 950 K while in the experiment the NTC region is from 740 K to 890 K. The predicted species concentrations can reproduce the trend of the experimental data, especially for O2, CO and CO2. The simulated laminar flame speed at 400 K and 470 K are with absolute averaged deviations of 3.5% and 4.06% respectively. The constant volume spray and combustion validations are reasonably good. In the engine combustion validations, a multistep soot model was embedded into the new jet fuel surrogate mechanism. The predicted in-cylinder pressure can reproduce the experimental data, expect for small deviations after the peak pressure (the averaged deviation is around 6.2% after the peak pressure). The embedded soot model can well reproduce the trend of the experimental data. It can be concluded that this new jet fuel surrogate mechanism is compact and robust for the utilization in diesel engine combustion simulation.

Fractal Analysis of Butanol/Gasoline Surrogate Blends Combustion in an Optical Direct-Injection Engine

Observation of Flame Propagation in a Heavy-Duty Natural-Gas Lean Burn Spark-Ignition Engine

An Experimental Investigation of Early Flame Development in an Optical Spark Ignition Engine Fueled with Natural Gas

Direct numerical simulations of rich premixed turbulent n-dodecane/air flames at diesel engine conditions

Structure and Propagation of Two-Dimensional, Partially Premixed, Laminar Flames in Diesel Engine Conditions

A Direct Numerical Simulation Study of Flame Structure and Stabilization of an Experimental High Ka CH4/air Premixed Jet Flame

Investigation of the Ignition Processes of a Multi-Injection Flame in a Diesel Engine Environment Using the Flamelet Model.

Combustion and Emissions of Isomeric Butanol/gasoline Surrogates Blends on an Optical GDI Engine

The Evolution of Soot Morphology and Nanostructure in Laminar Diffusion Flame of Surrogate Fuels for Diesel

An Optical Study on Liquid-Phase Penetration, Flame Lift-off Location and Soot Volume Fraction Distribution of Gasoline–diesel Blends in a Constant Volume Vessel

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

Experimental and Numerical Study of Soot Formation in Laminar Coflow Diffusion Flames of Gasoline/ethanol Blends

Investigating the Relationship Between Butanol Molecular Structure and Combustion Performance in an Optical SIDI Engine

Analysis of the fractal characteristics for combustion instability in a premixed natural gas engine

Flame area correlations with heat release at early flame development of combustion process in a spark-ignition direct-injection engine using gasoline, ethanol and butanol

Experimental and Kinetic Study of Diesel/gasoline Surrogate Blends over Wide Temperature and Pressure

Numerical study of spray combustion and soot emission of gasoline–biodiesel fuel under gasoline compression ignition-relevant conditions

Study on Combustion Characteristics of Ethanol Gasoline in Laminar Flame with Synchrotron Radiation

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

Laminar Flame Characteristics of Iso-Octane/n-butanol Blend–Air Mixtures at Elevated Temperatures

Measurement of the Instantaneous Flame Front Structure of Syngas Turbulent Premixed Flames at High Pressure