Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

An Optical Study on Liquid-Phase Penetration, Flame Lift-off Location and Soot Volume Fraction Distribution of Gasoline–diesel Blends in a Constant Volume Vessel

Experimental and Numerical Study of Soot Formation in Laminar Coflow Diffusion Flames of Gasoline/ethanol Blends

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

An optical study on the spray and combustion characteristics of coal-derived naphtha/diesel blends in a constant volume combustion chamber

Numerical Study of Soot Particles from Low Temperature Combustion of Engine Fueled with Diesel Fuel and Unsaturation Biodiesel Fuels

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Role of Dimethyl Ether in Incipient Soot Formation in Premixed Ethylene Flames

Large Eddy Simulation of Soot Formation in a Turbulent Lifted Flame with a Discretized Population Balance and a Reduced Kinetic Mechanism

Two-dimensional measurements of soot in a turbulent diffusion diesel flame: the effects of injection pressure, nozzle orifice diameter, and gas density

Experimental Investigation of Low-Temperature Autoignition in Turbulent Premixed Swirling Flames

Multiple optical diagnostics on effects of fuel properties on spray flames under oxygen-enriched conditions

Effects of fuel injection pressure and quantity on low octane gasoline sprays in a simulated high-pressure ambient environment of a gasoline compression ignition engine

Experimental and Numerical Investigation on Soot Volume Fractions and Number Densities in Non-Smoking Laminar N-Heptane/n-butanol Coflow Flames

Soot and Flame Structures in Turbulent Partially Premixed Jet Flames of Pre-Evaporated Diesel Surrogates with Admixture of OMEn

The Evolution of Soot Morphology and Nanostructure in Laminar Diffusion Flame of Surrogate Fuels for Diesel

Study of soot formations in co-flow laminar diffusion flames of n-heptane and oxygenated aromatic biofuels from atmospheric condition to 2.3 bar

A study of the sooting behavior of hydro-processed renewable jet and petroleum jet fuels in a laminar counter-flow flame

Numerical study of spray combustion and soot emission of gasoline–biodiesel fuel under gasoline compression ignition-relevant conditions

A quantitative study on deposited fuel film and microscopic droplet characteristics of gasoline surrogate fuel and ethanol spray impingement

Investigation of soot formation in the oxygenated fuels flame by laser induced fluorescence and incandescence

Spray Characteristics of a Gasoline-Diesel Blend (ULG75) Using High-Speed Imaging Techniques