Abstract:Rapid advancement of novel optical spectroscopy and imaging systems relies on the availability of well-characterised and reproducible protocols for phantoms as a standard for the validation of the technique. The tissue-mimicking phantoms are also used to investigate photon transport in biological samples before clinical trials that require well-characterized phantoms with known optical properties (reduced scattering (μ's) and absorption (μa) coefficients). However, at present, there is limited literature available providing well-characterized phantom recipes considering various biomarkers and tested over a wide range of optical properties covering most of the human organs and applicable to multimodal optical spectroscopy. In this study, gelatin-based phantoms were designed to simulate tissue optical properties where India ink and Intralipid were used as absorbing and scattering agents, respectively. Multiple biomarkers were simulated by varying the gelatin concentration to mimic the change in tissue hydration and hydroxyapatite concentration to mimic bone signature. The recipe along with biomarkers were optimized and characterised over a wide range of optical properties (μa from 0.1 to 0.5 cm-1; μ's from 5 to 15 cm-1) relevant to human tissue using a broadband time-domain diffuse optical spectrometer. The data collected showed a linear relationship between the concentration of ink/lipids and μa/μ's values with negligible coupling between μa and μ's values. While being stored in a refrigerator post-fabrication, the μa and μ's did not change significantly (<4% coefficient of variation, 'CV') over three weeks. The reproducibility in three different sets was validated experimentally and found to be strong with a variation of ≤6% CV in μa and ≤9% CV in μ's. From the 3 × 3 data of μa and μ's matrices, one can deduce the recipe for any target absorption or reduced scattering coefficient. The applicability of the phantoms was tested using diffuse reflectance and Raman spectrometers. A use case application was demonstrated for Raman spectroscopy where hydration and hydroxyapatite phantoms were designed to characterize the Raman instrument. The Raman instrument could detect the change in 1% of HA and 5% of hydration. This study presents a first-of-its-kind robust, well-characterized, multi-biomarker phantom recipe for calibration and benchmarking of multimodal spectroscopy devices assisting in their clinical translation.

A Solid Phantom Recipe and Exploration for Biophotonics Applications: a Step to Produce Standardized Tissue Phantoms

A Multiparameter Tissue-Mimicking Phantom for Multispectral Endoscopic Imaging

Fabrication and characterization of multi-biomarker optimized tissue-mimicking phantoms for multi-modal optical spectroscopy

3D printing of tissue-simulating phantoms as a traceable standard for biomedical optical measurement

Fabrication of Tuneable Tissue-Mimicking Phantom for Optical Methods

Optical Characterization of Tissue Mimicking Phantoms by a Vertical Double Integrating Sphere System

Geometrically complex 3D-printed phantoms for diffuse optical imaging

Phantom Preparation and Optical Property Determination

Developing Multifunctional Tissue Simulating Phantoms for Quantitative Biomedical Optical Imaging

Hybrid heterogeneous phantoms for biomedical applications: a demonstration to dosimetry validation

3d Printing Method For Freeform Fabrication Of Optical Phantoms Simulating Heterogeneous Biological Tissue

3D Printing of Tissue-Simulating Phantoms for Calibration of Biomedical Optical Devices

National Institute of Standards and Technology measurement service of the optical properties of biomedical phantoms: Current status

Tutorial on phantoms for photoacoustic imaging applications

Low-cost tissue simulating phantoms with adjustable wavelength-dependent scattering properties in the visible and infrared ranges

Characterization and Optimization of Dielectric Phantom Composition for Frequency-Dependent Tissue Mimicking

Development of a microstructured tissue phantom with adaptable optical properties for use with microscopes and fluorescence lifetime imaging systems

Multimodal 3D Printing of Phantoms to Simulate Biological Tissue.

Multi-layered silicone-based breast tissue phantom for multi-modal optical spectroscopy

Fabrication of a Multilayer Tissue-Mimicking Phantom with Tunable Optical Properties to Simulate Vascular Oxygenation and Perfusion for Optical Imaging Technology.

Development and optical characterisation of agarose-based phantoms mimicking biological tissues for studies of light penetration in the brain