Hydrogen detection with plasmonic palladium-coated tilted fiber Bragg gratings

Álvaro González-Vila,Shunshuo Cai,Tuan Guo,Christophe Caucheteur

DOI: https://doi.org/10.1364/sensors.2019.sw5d.5

2019-01-01

Abstract:Surface plasmon resonance excitation is achieved with palladium-coated tilted fiber Bragg gratings. The sensors are able to detect hydrogen leaks at concentrations way below the lower explosive limit of the gas.

What problem does this paper attempt to address?

Single‐Crystal Pd and Its Alloy Nanowires for Plasmon Propagation and Highly Sensitive Hydrogen Detection

Fuxing Gu,Heping Zeng,Y. B. Zhu,Qing Yang,L. K. Ang,Songlin Zhuang

DOI: https://doi.org/10.1002/adom.201300413

IF: 9

2014-01-01

Advanced Optical Materials

Abstract:In this work plasmon propagation and highly sensitive hydrogen sensing are demonstrated in single‐crystal Pd and its alloy nanowires, based on an evanescent wave coupling technique using optical fiber tapers. The plasmon propagation losses of Pd nanowires on an MgF2 substrate are measured to be ∼2 dB/μm (at 635 nm). Using a suspension scheme of the nanowire, the propagation losses decrease to ∼0.6 dB/μm in air. Utilizing an alloying technique, single‐crystal PdAg nanowires are fabricated and exhibit decreasing and tunable propagation losses. Furthermore, Pd nanowires are used for plasmonic gas sensing with amplitude sensitivity of ∼11 dB to 3.6% hydrogen gas, which is much higher than those in photonic nanowire sensors. The concentration detection limit is about 0.2%, which is lower than those in photonic nanowire sensors and most surface plasmon resonance sensors. The hysteresis effect of the Pd nanowire in hydrogen sensing is suppressed by using single‐crystal PdAu alloy nanowires. This work may find widespread application, ranging from sensing and integrated circuits to materials research.
A Reliable and Fast Hydrogen Gas Leakage Detector Based on Irreversible Cracking of Decorated Palladium Nanolayer Upon Aligned Polymer Fibers

Ran Chen,Xiaodong Ruan,Weiting Liu,Cesare Stefanini

DOI: https://doi.org/10.1016/j.ijhydene.2014.11.026

IF: 7.2

2014-01-01

International Journal of Hydrogen Energy

Abstract:A reliable fast response and non-maintenance hydrogen gas sensor is presented, which can be easily fabricated through sputtering palladium nanolayer onto uniaxially aligned electrospun polyurethane nanofibers. The designated palladium sensing nanolayer undergoes an irreversible cracking while being exposed to hydrogen gas, which induces a great resistance increases. Efficient and credible fabrication is investigated through a designed electrospinning device and the sensors show highly reliable response with good consistency. It has been shown that the sensor can detect hydrogen gas concentration as low as 20 ppm with response time less than 60 s and maximum relative resistance variance more than 70%. With its low-cost and easy-fabrication characteristics, this simplified nanofiber sensor provides an efficient and low cost solution for hydrogen leakage detection at scenarios where fast response, low concentration and room temperature working are essentially required. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
Tilted Fiber Bragg Grating Sensor Using Chemical Plating of a Palladium Membrane for the Detection of Hydrogen Leakage

Jiachen Yu,Zhenlin Wu,Xin Yang,Xiuyou Han,Mingshan Zhao

DOI: https://doi.org/10.3390/s18124478

IF: 3.9

2018-12-18

Sensors

Abstract:A tilted fiber Bragg grating (TFBG) hydrogen sensor coated with a palladium (Pd) membrane by the electroless plating method is proposed in this paper. A uniform layer of Pd metal is fabricated in aqueous solutions by the chemical coating method, which is used as the sensitive element to detect the change of the surrounding refractive index (SRI) caused by hydrogen absorption. The change in SRI causes an unsynchronized change of the cladding modes and the Bragg peak in the TFBG transmission spectrum, thereby eliminating the cross-sensitivity due to membrane expansion and is able to simultaneously monitor the presence of cracks in the pipe, as well as the hydrogen leakage. By subtracting the wavelength shift caused by fiber expansion, the change of SRI, i.e., the information from the H2 level, can be separately obtained. The drifted wavelength is measured for the H2 concentration below the hydrogen explosion limit between 1% and 4%. The chemical-based coating has the advantages of a low cost, a simple operation, and being suitable for coating on long fiber structures. The proposed sensor is able to detect the H2 signal in 5 min at a 1% H2 concentration. The proposed sensor is proved to be able to monitor the hydrogen level without the cross-sensitivity of temperature variation and expansion strains, so could be a good candidate for security applications in industry.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
An easy-fabricated hydrogen gas sensor based on palladium-decorated polyurethane nanofibers

Ran Chen,Weiting Liu,Xin Fu,Dario, P.

DOI: https://doi.org/10.1109/SAS.2014.6798941

2014-01-01

Abstract:This paper reports a hydrogen gas sensor based on palladium-decorated polyurethane nanofibers which can be easily fabricated through electrospinning, sputtering, gap generating and adjusting. Extremely narrow gaps between palladium nanostructures with width about 12nm are obtained through stretching aided hydrogen gas exposure and adjusted through further stretching which modulates measurement range and sensitivity of the sensor. This sensor performs a good and fast response (with response time less than 5s and recovery time less than 10s) to hydrogen gas of low concentrations with a good sensitivity and linearity in narrow range (with max sensitivity about 0.32% per ppm in relative resistance change and span less than 100ppm) and a fairly low limit-of-detection (which can be below 50ppm). Therefore, the sensor is suitable for hydrogen gas leak detection.
Polarization Property Associated with Surface Plasmon Resonance in a Palladium Thin-Film Coated Aluminum Grating in a Conical Mounting and Its Application to Hydrogen Gas Detection

Toyonori Matsuda,Isao Tsunoda,Shinichiro Koba,Yu Oshiro,Hiroyuki Odagawa

DOI: https://doi.org/10.3390/s24061990

IF: 3.9

2024-03-21

Sensors

Abstract:We have investigated a polarization property of the (specularly) reflected light from an aluminum grating, coated with a palladium (Pd) thin-film on its surface. The polarization property, which is associated with surface plasmon resonance (SPR), and occurs in the Pd thin-film on the aluminum grating in a conical mounting, is observed as a rapid change in the normalized Stokes parameter s3, around the resonance angle, θsp, at which point, SPR occurs. The sensing technique used the rapid change in s3 to allow us to successfully detect a small change in the complex refractive index of the Pd thin-film layer upon exposure to hydrogen gas, with a concentration near the lower explosion level. Experimental results showed that the sensing technique provided a sensitive and stable response when the Pd thin-film layer was exposed to gas mixtures containing hydrogen at concentrations of 1 to 4% (by volume) in nitrogen.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Potential to Detect Hydrogen Concentration Gradients with Palladium Infused Mesoporous-Titania on D-Shaped Optical Fiber

Zsolt L Poole,Paul R Ohodnicki,Aidong Yan,Yuankun Lin,Kevin P Chen

DOI: https://doi.org/10.1021/acssensors.6b00583

2017-01-27

Abstract:A distributed sensing capable high temperature D-shaped optical fiber modified with a palladium nanoparticle sensitized mesoporous (∼5 nm) TiO2 film, is demonstrated. The refractive index of the TiO2 film was reduced using block copolymer templating in order to realize a mesoporous matrix, accommodating integration with optical fiber. The constructed sensor was analyzed by performing direct transmission loss measurements, and by analyzing the behavior of an integrated fiber Bragg grating. The inscribed grating should reveal whether the refractive index of the composite film experiences changes upon exposure to hydrogen. In addition, with frequency domain reflectometry the distributed sensing potential of the developed sensor for hydrogen concentrations of up to 10% is examined. The results show the possibility of detecting chemical gradients with sub-cm resolution at temperatures greater than 500 °C.
Experimental Research of Optical Fiber Hydrogen Gas Sensing System Based on Palladium-Silver Alloy

Lu-jun Cui,Gao-feng Zhou,Zheng-feng Li,Yan-long Cao

DOI: https://doi.org/10.1007/s11801-016-6168-1

2016-01-01

Optoelectronics Letters

Abstract:A novel optical fiber hydrogen sensing system based on palladium (Pd) and sliver (Ag) is proposed. By direct current (DC) magnetron process, Pd/Ag alloy ultra-thin films were deposited on the substrate to eliminate the hydrogen embrittlement of sensor based on pure Pd. Several samples with different thin film thicknesses were fabricated at different substrate temperatures and tested in the optical fiber hydrogen sensor setup. We do a series of experiments for obtaining optimum sputtering parameters, such as optimum sputtering temperature and thickness of Pd/Ag alloy film. The humidity effect and reliability experiment for the optical fiber hydrogen gas sensor are reported in detail. The testing results demonstrate the Pd/Ag alloy is a promising material for optical fiber hydrogen gas sensor.
Chiral Plasmonic Hydrogen Sensors

Marcus Matuschek,Dhruv Pratap Singh,Hyeon-Ho Jeong,Maxim Nesterov,Thomas Weiss,Peer Fischer,Frank Neubrech,Na Liu

DOI: https://doi.org/10.1002/smll.201702990

2021-04-30

Abstract:In this article, a chiral plasmonic hydrogen-sensing platform using palladium-based nanohelices is demonstrated. Such 3D chiral nanostructures fabricated by nanoglancing angle deposition exhibit strong circular dichroism both experimentally and theoretically. The chiroptical properties of the palladium nanohelices are altered upon hydrogen uptake and sensitively depend on the hydrogen concentration. Such properties are well suited for remote and spark-free hydrogen sensing in the flammable range. Hysteresis is reduced, when an increasing amount of gold is utilized in the palladium-gold hybrid helices. As a result, the linearity of the circular dichroism in response to hydrogen is significantly improved. The chiral plasmonic sensor scheme is of potential interest for hydrogen-sensing applications, where good linearity and high sensitivity are required.

Applied Physics,Optics
Micro Hydrogen Sensor Based on Pd-Ag Nanofilm

Ying Feng,Min Wang

2006-01-01

Abstract:In this paper,palladium-silver （Pd-Ag） system was studied for hydrogen sensing.Nanofilm of Pd-Ag was fabricated on a porous ceramic substrate through a combination of microfabrication techniques.The electric resistance of the zigzag-shaped microstructure was measured toward hydrogen concentration change.The sensing element demonstrates high sensitivity,fast response and fast recovery to hydrogen.The Pd-Ag film was characterized by scanning electron microscopy （SEM） equipped with X probe to correlate its physical and chemical properties to its sensing performance.The present sensor is very promising for room temperature hydrogen leakage detection and related applications.The temperature effect on the sensing performance of the metal film was also investigated.
Fabry–Pérot Cavities with Suspended Palladium Membranes on Optical Fibers for Highly Sensitive Hydrogen Sensing

Feng Xu,Jun Ma,Can Li,Churong Ma,Jie Li,Bai-Ou Guan,Kai Chen

DOI: https://doi.org/10.3390/molecules28196984

IF: 4.6

2023-10-10

Molecules

Abstract:Hydrogen (H2) sensors are critical to various applications such as the situation where H2 is used as the clean energy for industry or the indicator for human disease diagnosis. Palladium (Pd) is widely used as the hydrogen sensing material in different types of sensors. Optical fiber H2 sensors are particularly promising due to their compactness and spark-free operation. Here, we report a Fabry–Pérot (FP)-cavity-based H2 sensor that is formed with a freestanding Pd membrane and integrated on a conventional single-mode optical fiber end. The freestanding Pd membrane acts both as the active hydrogen sensing material and as one of the reflective mirrors of the cavity. When the Pd film absorbs H2 to form PdHx, it will be stretched, resulting in a change of the cavity length and thus a shift of the interference spectrum. The H2 concentration can be derived from the amplitude of the wavelength shift. Experimental results showed that H2 sensors based on suspended Pd membranes can achieve a detection sensitivity of about 3.6 pm/ppm and a detection limit of about 3.3 ppm. This highly sensitive detection scheme is expected to find applications for sensing low-concentration H2.

chemistry, multidisciplinary,biochemistry & molecular biology
Ultrasensitive and fast single wavelength plasmonic hydrogen sensing with anisotropic nanostructured Pd films

William L. Watkins,Yves Borensztein

DOI: https://doi.org/10.48550/arXiv.1807.07296

IF: 2.552

2018-07-19

Chemical Physics

Abstract:Anisotropic nanostructured porous Pd films are fabricated using oblique angle deposition in vacuum on a glass substrate. They display a dichroic response, due to localised surface plasmon resonances (LSPR) within the nanoparticles forming the film, dependent on the incident light polarisation. Ultrasensitive hydrogen sensing is reached by using these films in conjunction with a differential optical technique derived from the reflectance anisotropy spectroscopy. The evolution of the samples optical responses is monitored during the formation of Pd hydride in both the dilute alpha-phase and the dense beta-phase, whilst the samples are exposed to different concentration of H2 in Ar (from 100 percent H2 to a few ppm). The measurements are performed at a single wavelength in the visible range and at 22 deg C. The results show that a quantitative measurement of the hydrogen concentration in a carrier gas can be measured throughout the concentration range. The limit of detection is 10 ppm and the time for detecting the presence of H2 in the carrying gas is below one second at concentration down to 0.25 percent of H2 in Ar. Furthermore, the optical anisotropy of the samples and its evolution with exposure to H2 are correctly reproduced with an effective medium theory.
Optical fiber hydrogen sensor using metasurfaces composed of palladium

Shunshuo Cai,Wanhan Hu,Yiman Liu,Juan Ning,Sixuan Feng,Chao Jin,Lingling Huang,Xin Li

DOI: https://doi.org/10.3788/col202220.053601

IF: 2.56

2022-01-01

Chinese Optics Letters

Abstract:Shunshuo Cai, Wanhan Hu, Yiman Liu, Juan Ning, Sixuan Feng, Chao Jin, Lingling Huang, Xin LiPalladium-based hydrogen sensors have been typically studied due to the dielectric function that changes with the hydrogen concentration. ... [Chin. Opt. Lett. 20, 053601- (2022)]

optics
Ultrahigh sensitivity of hydrogen detection with a perforated Pd film on a miniature fiber tip

Feng Xu,Jun Ma,Kaiqiang Hu,Zhiliang Zhang,Churong Ma,Bai-Ou Guan,Kai Chen

DOI: https://doi.org/10.1016/j.snb.2023.134875

IF: 9.221

2023-11-04

Sensors and Actuators B Chemical

Abstract:Hydrogen (H 2 ) is a renewable energy gas and an important industrial raw material playing important roles in many fields. However, H 2 is colorless, odorless and highly flammable within a wide concentration range. So H 2 detection is very important for leakage monitoring especially at low concentration. Here we propose an ultrahigh sensitivity H 2 sensor with a perforated palladium (Pd) film on the tip of an optical fiber. The suspended Pd nanohole film forms a Fabry-Pérot (FP) interferometer with a silica capillary fused onto the fiber. Upon H 2 adsorption, the Pd nanohole film bends inwards leading to spectral shift of the FP cavity. With the film perforated, its Young's modulus becomes effectively smaller giving rise to larger spectral shift and higher H 2 sensitivity. We experimentally studied the effect of the structural parameters of the holey film on the H 2 sensing performance and achieved a H 2 detection sensitivity of 7.1 pm/ppm and a detection limit of 1.7 ppm. The sensor also shows good repeatability and gas selectivity and is expected to find applications as optical H 2 sensors working at low concentrations.

chemistry, analytical,electrochemistry,instruments & instrumentation
Hydrogen and temperature measurement using a functionalized superstructure of Bragg gratings in a helical-core fiber

Yanyan Zhi,Yanyu Hu,Hao Chen,Shuling Zhang,Jie Li,Hao Liang,Chuang Wu,Bai-Ou Guan

DOI: https://doi.org/10.1016/j.optlastec.2024.110551

IF: 4.939

2024-07-01

Optics & Laser Technology

Abstract:As decarbonization is urgent in global climate, hydrogen, of which the product is pure water after burning, becomes a potentially clean and sustainable energy source as a replacement for fossil fuels. However, the hydrogen storge is challenging due to the highly flammable and explosive properties, limiting its enormous applications in industries. Real-time and sensitive detection of hydrogen is thus imperative to avoid leakage accidents, while the sensors based on electric signals have the risk of spark or arc discharge which may induce explosion. Here, we propose and experimentally demonstrate an optical hydrogen sensor using a functionalized superstructure of Bragg gratings in a helical-core fiber with a thin palladium film. Due to the cross sensing of the two sets of gratings, simultaneous detection of hydrogen concentration and temperature can be realized. By modifying the device diameter using wet etching technique, the sensitivity of hydrogen concentration is enhanced by 2.7 times. The utilization of the superstructure of Bragg gratings sampled in the helical-core fiber provides a promising platform for reliable and safe sensing of hydrogen with the ability of simultaneous monitoring of temperature.

optics,physics, applied
Surface Plasmon Resonance Hydrogen Sensor by Using a Au-Pd Thin Film Transducing Layer

胡建东,王晓萍,文泓桥

DOI: https://doi.org/10.3321/j.issn:1002-1582.2004.06.036

2004-01-01

Optical Technique

Abstract:A novel hydrogen sensor coated a combined Au and Pd thin film is investigated. Unlike a singular Pd thin film sensor, the new structure is high durable, high response value and high sensitive. A corresponding mathematic model based on surface plasmon resonance(SPR) hydrogen sensors is established. The sensitivity of SPR hydrogen sensor is modeled. The simulation result shows that the optimal layer configuration for SPR hydrogen sensors should be Au (2nm)/Pd (20nm) for achieving best performance. Compared to a traditional singular Pd hydrogen sensor, the sensitivity of the new hydrogen sensor is increased by 49.4%.
Spectrometer‐free Optical Hydrogen Sensing Based on Fano‐like Spatial Distribution of Transmission in a Metal−Insulator−Metal Plasmonic Doppler Grating

Yi‐Ju Chen,Fan‐Cheng Lin,Ankit Kumar Singh,Lei Ouyang,Jer‐Shing Huang

DOI: https://doi.org/10.1002/adom.202100869

IF: 9

2021-09-12

Advanced Optical Materials

Abstract:Optical nanosensors are promising for hydrogen sensing because they are small, free from spark generation, and feasible for remote optical readout. Conventional optical nanosensors require broadband excitation and spectrometers, rendering the devices bulky and complex. An alternative is spatial intensity-based optical sensing, which only requires an imaging system and a smartly designed platform to report the spatial distribution of analytical optical signals. Here, a spatial intensity-based hydrogen sensing platform is presented based on Fano-like spatial distribution of the transmission in a Pd-Al2O3-Au metal-insulator-metal plasmonic Doppler grating (MIM-PDG). The MIM-PDG manifests the Fano resonance as an asymmetric spatial transmission intensity profile. The absorption of hydrogen changes the spatial Fano-like transmission profiles, which can be analyzed with a "spatial" Fano resonance model and the extracted Fano resonance parameters can be used to establish analytical calibration lines. While gratings sensitive to hydrogen absorption are suitable for hydrogen sensing, hydrogen insensitive gratings are also found, which provide an unperturbed reference signal and may find applications in nanophotonic devices that require a stable optical response under fluctuating hydrogen atmosphere. The MIM-PDG platform is a spectrometer-free and intensity-based optical sensor that requires only an imaging system, making it promising for cellphone-based optical sensing applications.

materials science, multidisciplinary,optics
Hydrogen Sensor Based on Polymer-Filled Hollow Core Fiber with Pt-Loaded Wo3/Sio2 Coating

Ben Xu,Ping Li,D. N. Wang,Chun-Liu Zhao,Jixiang Dai,Minghong Yang

DOI: https://doi.org/10.1016/j.snb.2017.01.206

2017-01-01

Abstract:A simple, compact and highly sensitive hydrogen sensing device based on a polymer-filled hollow core fiber coated with Pt-loaded WO3/SiO2 is demonstrated. The device is composed of a tiny segment of hollow core fiber (HCF) spliced to a standard single mode fiber (SMF) incorporated with a fiber Bragg grating (FBG). The HCF is filled with polymer and the inner air-gap near the interface between SMF and polymer forms a micro-cavity Fabry-Perot interferometer (FPI). With Pt-loaded WO3/SiO2 coating acting as the catalytic layer, hydrogen undergoes an exothermic reaction with oxygen in air and releases heat when the device is exposed to hydrogen, which induces local temperature change of FPI and hence leads to reflection spectrum shift of the proposed device. Here, the FBG is used to compensate the surrounding temperature effect and eliminate the temperature cross-sensitivity of the device. A wavelength shift of over 35 nm is obtained with a 242-mu m-long polymer-filled HCF for 4% (vol%) H-2 concentration, and the maximum sensitivity of 17.48 nm/% (vol%) H-2 is achieved within the range of 0-4.0% (Vol%) H-2 in air. The sensor device also exhibits fast response time to hydrogen. (C) 2017 Elsevier B.V. All rights reserved.
Spectrometer-free optical hydrogen sensing based on Fano-like spatial distribution of transmission in a metal-insulator-metal plasmonic Doppler grating

Yi-Ju Chen,Fan-Cheng Lin,Ankit Kumar Singh,Lei Ouyang,Jer-Shing Huang

DOI: https://doi.org/10.48550/arXiv.2105.00367

2021-05-02

Abstract:Optical nanosensors are promising for hydrogen sensing because they are small, free from spark generation, and feasible for remote optical readout. Conventional optical nanosensors require broadband excitation and spectrometers, rendering the devices bulky and complex. An alternative is spatial intensity-based optical sensing, which only requires an imaging system and a smartly designed platform to report the spatial distribution of analytical optical signals. Here, we present a spatial intensity-based hydrogen sensing platform based on Fano-like spatial distribution of the transmission in a Pd-Al2O3-Au metal-insulator-metal plasmonic Doppler grating (MIM-PDG). The MIM-PDG manifests the Fano resonance as an asymmetric spatial transmission intensity profile. The absorption of hydrogen changes the spatial Fano-like transmission profiles, which can be analyzed with a "spatial" Fano-resonance model and the extracted Fano resonance parameters can be used to establish analytical calibration lines. While gratings sensitive to hydrogen absorption are suitable for hydrogen sensing, we also found hydrogen insensitive gratings, which provide an unperturbed reference signal and may find applications in nanophotonic devices, that require a stable optical response under fluctuating hydrogen atmosphere. The MIM-PDG platform is a spectrometer-free and intensity-based optical sensor that requires only an imaging system, making it promising for cellphone-based optical sensing applications.

Optics,Mesoscale and Nanoscale Physics,Materials Science
Aqueous phase Localized Surface Plasmon Resonance based Hydrogen sensing using Mixed colloidal Ag and PdAu nanoparticles

Qianxi Chen,Jiaxi Tang,Hong Shao,Changyu Tang,Dongmei Wang,Meikun Fan

DOI: https://doi.org/10.1016/j.matlet.2024.137716

IF: 3

2024-11-23

Materials Letters

Abstract:Hydrogen sensing is critical for its role in clean energy technologies. Herein, a colloidal Ag-PdAu ternary system as an efficient Localized Surface Plasmon Resonance (LSPR)-based sensor is first proposed for H 2 sensing in aqueous environments. Upon exposure to H 2 , the system exhibits a significant LSPR peak shift of 42 nm within just 10 min, with no observable response to N 2 under identical conditions.

materials science, multidisciplinary,physics, applied
Sub-second and ppm-level Optical Sensing of Hydrogen Using Templated Control of Nano-hydride Geometry and Composition

Hoang Mai Luong,Minh Thien Pham,Tyler Guin,Richa Pokharel Madhogaria,Manh-Huong Phan,George K. Larsen,Tho Duc Nguyen

DOI: https://doi.org/10.1038/s41467-021-22697-w

2021-03-01

Abstract:The use of hydrogen as a clean and renewable alternative to fossil fuels requires a suite of flammability mitigating technologies, particularly robust sensors for hydrogen leak detection and concentration monitoring. To this end, we have developed a class of lightweight optical hydrogen sensors based on a metasurface of Pd nano-patchy particle arrays, which fulfills the increasing requirements of a safe hydrogen fuel sensing system with no risk of sparking. The structure of the optical sensor is readily nano-engineered to yield extraordinarily rapid response to hydrogen gas (<3 s at 1 mbar H$_{2}$) with a high degree of accuracy (<5%). By incorporating 20% Ag, Au or Co, the sensing performances of the Pd-alloy sensor are significantly enhanced, especially for the Pd$_{80}$Co$_{20}$ sensor whose optical response time at 1 mbar of H$_{2}$ is just ~0.85 s, while preserving the excellent accuracy (<2.5%), limit of detection (2.5 ppm), and robustness against aging, temperature, and interfering gases. The superior performance of our sensor places it among the fastest and most sensitive optical hydrogen sensors.

Materials Science

Hydrogen detection with plasmonic palladium-coated tilted fiber Bragg gratings

Single‐Crystal Pd and Its Alloy Nanowires for Plasmon Propagation and Highly Sensitive Hydrogen Detection

A Reliable and Fast Hydrogen Gas Leakage Detector Based on Irreversible Cracking of Decorated Palladium Nanolayer Upon Aligned Polymer Fibers

Tilted Fiber Bragg Grating Sensor Using Chemical Plating of a Palladium Membrane for the Detection of Hydrogen Leakage

An easy-fabricated hydrogen gas sensor based on palladium-decorated polyurethane nanofibers

Polarization Property Associated with Surface Plasmon Resonance in a Palladium Thin-Film Coated Aluminum Grating in a Conical Mounting and Its Application to Hydrogen Gas Detection

Potential to Detect Hydrogen Concentration Gradients with Palladium Infused Mesoporous-Titania on D-Shaped Optical Fiber

Experimental Research of Optical Fiber Hydrogen Gas Sensing System Based on Palladium-Silver Alloy

Chiral Plasmonic Hydrogen Sensors

Micro Hydrogen Sensor Based on Pd-Ag Nanofilm

Fabry–Pérot Cavities with Suspended Palladium Membranes on Optical Fibers for Highly Sensitive Hydrogen Sensing

Ultrasensitive and fast single wavelength plasmonic hydrogen sensing with anisotropic nanostructured Pd films

Optical fiber hydrogen sensor using metasurfaces composed of palladium

Ultrahigh sensitivity of hydrogen detection with a perforated Pd film on a miniature fiber tip

Hydrogen and temperature measurement using a functionalized superstructure of Bragg gratings in a helical-core fiber

Surface Plasmon Resonance Hydrogen Sensor by Using a Au-Pd Thin Film Transducing Layer

Spectrometer‐free Optical Hydrogen Sensing Based on Fano‐like Spatial Distribution of Transmission in a Metal−Insulator−Metal Plasmonic Doppler Grating

Hydrogen Sensor Based on Polymer-Filled Hollow Core Fiber with Pt-Loaded Wo3/Sio2 Coating

Spectrometer-free optical hydrogen sensing based on Fano-like spatial distribution of transmission in a metal-insulator-metal plasmonic Doppler grating

Aqueous phase Localized Surface Plasmon Resonance based Hydrogen sensing using Mixed colloidal Ag and PdAu nanoparticles

Sub-second and ppm-level Optical Sensing of Hydrogen Using Templated Control of Nano-hydride Geometry and Composition