Abstract:The work presented in this paper focused on the effects of laser remelting with varied laser energy densities from 800 J/mm to 1400 J/mm on the phase transformation and microstructural characteristics in the tungsten carbide nickel-based matrix composite (Ni-WC) tracks obtained by laser hot wire cladding. The microstructures of the as-deposited tracks fabricated by laser hot-wire deposition were mainly composed of spherical residual carbons, eutectic Ni/Ni3B, retained WC/W2C particles and the granular in situ W2C particles formed in the interdendritic regions of primary (Ni,Fe) dendrites. When the low laser energy densities of 800 J/mm and 1000 J/mm were applied, the dispersive W2C particles in the as-deposited tracks were dissolved, and the WC particles were successfully in situ synthesized and uniformly distributed in the remelted tracks. When the laser energy density was increased to 1200 J/mm, the feather-like M6C(Ni2W4C) carbides homogeneously precipitated in the remelted tracks. When the laser energy density was further increased to 1400 J/mm, the dissolution degree of the ex-situ WC/W2C particles was significantly increased, resulting in a remelted track with a relative low volume fraction of retained ceramic particles and a high dilution ratio of the base metal. In addition, the dendritic M6C(Fe3W3C) carbides were precipitated around the retained particles, and the eutectic M6C(Fe3W3C) carbides in the herringbone morphology were uniformly distributed in the matrix of the track remelted by a high laser energy density of 1400 J/mm. These experimental results confirmed that the homogenization of the in situ synthesized reinforcements in the tracks could be well realized by laser hot wire cladding and the subsequent laser remelting. The coatings remelted by the low energy densities (800 J/mm and 1000 J/mm) possessed higher wear resistance than that of the as-deposited coating, but the wear performance of the remelted coatings was decreased when the laser energy densities were increased to 1200 J/mm and 1400 J/mm. (c) 2022 Published by Elsevier B.V.

Effect of laser remelting on microstructure and properties of WC reinforced Fe-based amorphous composite coatings by laser cladding

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Influence of laser remelting on organization, mechanical properties and corrosion resistance of Fe-based amorphous composite coating

Fabrication of Fe-based amorphous composite coating by laser cladding

Effects of Laser Re-Melting and Annealing on Microstructure, Mechanical Property and Corrosion Resistance of Fe-Based Amorphous/Crystalline Composite Coating

Study on the Effect of Laser Remelting Energy Density on the Microstructure and Wear Resistance of Fe-Based Alloy Coatings Fabricated by Laser Cladding

Effects of Laser Remelting on Microstructure, Wear Resistance, and Impact Resistance of Laser-Clad Inconel625-Ni/WC Composite Coating on Cr12MoV Steel

Effect of laser remelting on the organization and properties of WC/Ni-based coatings generated in situ by laser cladding

Effect of WC–Co addition on tribological and cracking behavior of laser cladded Fe-based amorphous/crystalline composite coatings

Synthesis of Fe–Ni–B–Si–Nb Amorphous and Crystalline Composite Coatings by Laser Cladding and Remelting

Effect of Laser Remelting on Corrosion and Wear Resistance of Fe82Cr16SiB Alloy Coatings Fabricated by Extreme High-Speed Laser Cladding

Effect of laser scanning speed on microstructure and properties of Fe based amorphous/ nanocrystalline cladding coatings

Formation and beneficial effects of the amorphous/nanocrystalline phase in laser remelted (FeCoCrNi)75Nb10B8Si7 high-entropy alloy coatings fabricated by plasma cladding

Influence of laser remelting on the microstructure and properties of Mo 2 FeB 2 ternary boride coatings prepared by laser cladding

Microstructure and wear resistance of laser cladding FeNiCrMo-WC composite coating

Microstructures and corrosion resistance of Fe-based amorphous/nanocrystalline coating fabricated by laser cladding

Surface microstructures and properties of oxide-reinforced FeCrAl matrix composite coatings prepared by laser cladding on a ferritic-martensitic steel

Effects of laser remelting on microstructural characteristics of Ni-WC composite coatings produced by laser hot wire cladding

Microstructure and Wear Resistance of Fe-Cr-Mo-Co-C-B Amorphous Composite Coatings Synthesized by Laser Cladding

Microstructure and mechanical properties of Fe-based amorphous alloy coatings prepared by ultra-high speed laser cladding

Research on Laser Preparation and Microstructure of Fe41Co7Cr15Mo14C15B6Y2 Alloy Coating