Abstract:Accelerated bridge construction, with innovative connection details and construction technologies, has been extensively investigated and put into practical application for years. Nowadays, there are three commonly used connection methods of accelerated bridge construction technology, namely, lap‐spliced connection, sleeve connection, and socket connection. Due to the convenience of construction and lower requirements of construction accuracy, the socket connection is more suitable for reconstruction and expansion projects of traffic infrastructure, which could minimize the impact on traffic and accelerate construction progress. According to the structural characteristics of the socket connection, there are some design parameters that may significantly affect the seismic resistance of the structure, such as socket embedment length, fabrication of the shear key, and grouting material strength. To fully study the influence of different design parameters on structural performance, an experiment was carried out to investigate the seismic behavior of the precast pier‐footing socket connections with different design parameters. Five 1:2 scale reinforced concrete precast pier‐footing socket connection specimens with different design parameters were designed and tested under cyclically reversed horizontal loads. The development of hysteresis features, failure mode, load‐bearing capacity, stiffness degradation, structural ductility, energy dissipation capacity, and residual drift are analyzed to reveal the influence of the different design parameters on the seismic behavior of the precast pier‐footing socket connection. The seismic behavior of the precast pier‐footing socket connection was significantly influenced by the embedment length especially when the embedment length was less than 1.0bc. When the embedment length was 0.5bc, the failure mode changed from bending damage at the bottom of the precast pier to the anchorage failure of the precast pier‐footing socket connection. When the embedment length was 1.5bc, the fabrication of the shear key had limited improvement on the seismic performance of the specimen, while reducing the ductility of the specimen. When the embedment length was 1.0bc, the grouting material with a strength grade of C60 could be used in the socket connection between the precast pier and footing. The research presented in this paper provides some design suggestions and a technical basis for evaluating the seismic behavior of precast pier‐footing structures with socket connection.

Experimental and numerical study of precast bridge piers with a new UHPC socket column-footing connection

Quasi-static testing of UHPC cupped socket piers-footing connection and its seismic fragility analysis under near-fault ground motions

Experimental Studies on Precast Prestressed Concrete Pile to Cip Concrete Pile-Cap Connections

The Influence of Socket Depth on the Seismic Behavior of Precast Hollow Bridge Pier

Experimental investigation of seismic behavior of precast pier‐footing socket connection with different design parameters

Seismic performance of precast piers with staggered longitudinal reinforcement-UHPC connection

Fatigue performance of a simply-supported T-beam UHPC bridge deck variable section joint structure

Seismic performance of a new type of prefabricated bridge pier with cast-in-place UHPC jacketing

Research on the Seismic Performance of Prefabricated Bridge Piers Using UHPC Grout under an Eccentric Load

Connections between precast hollow concrete columns and foundations using UHPC and rebar lap splices

Experimental and Numerical Investigations of the Impact Resistance of Socket and Pocket Connections for Precast Bridge Columns

Quasi-static tests and seismic fragility analysis of RC bridge piers with high-strength steel bars and high-strength/ultra-high performance concrete

Behavior and strength of headed stud shear connectors in ultra-high performance concrete of composite bridges

Precast steel—UHPC lightweight composite bridge for accelerated bridge construction

Shear performance and failure mechanism of socket CFST column-beam connection with UHPC grouting

Precast segmental piers: testing, modeling and seismic assessment of an emulative connection based on a grouted central tenon

Vehicular impact resistance of highway bridge with seismically-designed UHPC pier

Effect of interface treatment on the flexural performance of existing RC bridge beams strengthened with UHPC

Experimental Study on Seismic Performance of Precast Pretensioned Prestressed Concrete Beam-Column Interior Joints Using UHPC for Connection

Experimental and numerical studies on shear behavior of prefabricated bridge deck slabs with compact UHPC wet joint

Experimental Studies on Seismic Performance of Socket Connections with Shear Keys and Inner and Outer Filled Reinforced Concrete