Abstract:In-Vessel Retention (IVR) strategy for nuclear reactors in case of a Severe Accident (SA) intends to stabilize and retain the corium in the vessel by using the vessel wall as a heat exchanger with an external water loop. This strategy relies on simple actions to be passively taken as soon as SA signal is raised: vessel depressurization and reactor pit flooding. Then, the strategy is successful if the vessel keeps it integrity, which means that the heat flux coming from the corium pool does not exceed the cooling capacity of the External Reactor Vessel Cooling (ERVC) at each location along the vessel wall (no vessel melt-through) and the ablated vessel wall is mechanically resistant. The main uncertainties in this IVR safety evaluation are associated to the thermal load applied from the corium pool to the vessel wall and the resulting minimum vessel thickness after ablation. Indeed, the heat fluxes distribution along the vessel wall is directly dependent on the corium stratification which occurs as aresult of thermochemical interactions in the pool: when liquid steel is mixed with UO2 and partially oxidized Zr coming from the degradation of the fuel and claddings, there is a phase separation between oxide and metal phases due to a gap of miscibility. The primordial impact of the corium behaviour in the lower plenum of the reactor vessel on the IVR safety evaluation was clearly highlighted in the Phenomena Identification Ranking Table (PIRT) on IVR performed in the frame of the European IVMR (In-Vessel Melt Retention) project (Fichot et al., 2019). As a result, the focus is made in this paper on the critical points which impact the value of the minimum vessel thickness orequivalently the maximum heat flux reached at the outer surface of the vessel wall. Efficiency of the ERVC and mechanical resistance of the vessel wall are consequently not discussed here.The main objective is to identify the generic critical situations leading to an excessive heat flux to the vessel wall and the investigation of possible means to avoid them. In this perspective, the calculations of IVR strategy done by the project partners for different reactor designs and accident scenarios were used as a database to identify and understand the occurrence of critical configurations with excessive heat flux to the vessel wall. The results of 25 sequences are used, which correspond to 9 different reactor designs: a generic PWR 900MWe, a PWR 1100MWe with heavy reflector, a generic PWR 1300MWe, a generic Konvoi 1300MWe, a generic German BWR69, aNordic BWR, a BWR-5 Mark II, a VVER1000 and a VVER440/v213. In addition, different SA integral codes (ASTEC, ATHLET-CD, MAAP -combined with MAAP_EDF and PROCOR codes for simulation of lower plenum behavior-, MELCOR and RELAP/SCDAPSIM codes) are used.

The Influence of Flooding Water Level on Cooling Limit of RPV Outer Wall under ERVC Conditions

Experimental Research on Influence of Real Surface Material and Aging Effect on ERVC-CHF of RPV

Numerical study on the thermal hydraulic characteristics of ERVC system

CHF experiments and prediction model under subcooling flow boiling condition in passive IVR-ERVC system

Numerical Investigation on the Thermal-Hydraulic Characteristics near a Corroded Lower Head of the Reactor Vessel During IVR-ERVC

Experimental Investigation of 3-D ERVC Process for IVR Strategy – CHF Limits and Visualization of Boiling Phenomena

CFD study on flow-boiling characteristics and predicting critical heat flux under natural circulation conditions of IVR-ERVC

Experimental Study on CHF Using a Full Scale 2-D Curved Test Section with Additives and SA508 Heater for IVR-ERVC Strategy

In-Vessel Retention of Molten Core Debris for CAP1400

Prediction Of subcooled water flow boiling critical heat flux (CHF) at low pressure

Flow boiling experiments for CHF evaluation under downward-facing heating including flow visualization: Effects of pressure, orientation, mass flux, and local quality

Evaluation of Passive Circulation Flow Characteristics and Chf under In-Vessel Retention

Effect of Coolant Water Temperature of ECCS on Failure Probability of RPV

ICONE19-43276 Preliminary Study on In-Vessel Retention in Large-Scale Advanced PWR

Research on Uncertainty Analysis of In-Vessel Retention Parameters in Advanced PWR

A CHF Correlation and Flow Pattern Observation on a Downward-Facing Boiling Surface

Effect of Coolant Water Temperature of Emergency Core Cooling System on Failure Probability of Reactor Pressure Vessel

The comprehensive analysis of coolability limits of passive external reactor vessel cooling under in-vessel retention

Heat Transfer Experiment with the Prototypical Ra Number of Heavy Metallic Layer in IVR Strategy

Analysis of critical points of the In-Vessel Retention safety evaluation

Effect of Grooves on Nucleate Boiling Heat Transfer from Downward Facing Hemispherical Surface