Abstract:Black phosphorus has attracted broad interest because of their low-dimensional effect, and has become a new kind of two-dimensional (2D) materials. Phosphorus has several allotropes. Black phosphorus is the most thermodynamic stable in them. As a kind of two-dimensional materials, black phosphorus has high carrier mobility and on/off ratio. The band gap of black phosphorus can be adjusted by its number of layers from 0.3 to 2 eV. It is of great significance to the development of new infrared and near-infrared optoelectronic devices. Currently, the main methods for preparing black phosphorus are chemical vapor transfer and high energy ball milling methods. In this paper, black phosphorus was successfully synthesized from red phosphorus via chemical vapor transfer and high energy ball milling methods. Then black phosphorus was put in ethanol for 10 min to liquid exfoliation, in which the ultrasonic power was 400 W. The microstructures and stability of black phosphorus synthesized by two methods were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimeter (DSC). In situ electrical measurements of black phosphorus prepared by chemical vapor transfer were performed using a commercial scanning tunnelling microscope-transmission electron microscope probing system (STM-TEM, Nanofactory Instruments) inserted into a JEOL-2010F TEM. The microstructural characterization results show that there is some red phosphorus and amorphous phases in black phosphorus prepared by high energy ball milling method. On the contrary, the black phosphorus prepared by chemical vapor transfer method has no amorphous phases. The XRD results show that black phosphorus synthesized by chemical vapor transfer method did not change significantly after keeping in the air for 16 days. The DSC results show that the volatile points of the black phosphorus prepared by high energy ball milling and chemical vapor transfer methods are respectively 394.5 and 432.2 degrees C, which means the latter has better thermal stability. The TEM results show that a layer or two layers of phosphorene via liquid exfoliation had been obtained, which is large in size and clean in surface. After being irradiated in TEM with a dose of 0.8 eV/(angstrom(2).s) at 200 kV for 60 min, few new diffraction spots appeared in black phosphorus synthesized by chemical vapor transfer method, which indicates it is relatively stable under electron radiation in vacuum. In a word, the black phosphorus prepared by chemical vapor transfer method has large size, good crystallinity, high purity, and high stability. It can be used to prepare two-dimensional black phosphorus by mechanical exfoliation and liquid exfoliation, and then be applied to advanced microelectronic devices.

Introduction and Characterization of Phosphorus Nanomaterials

Optical, Optoelectronic, and Photocatalytic Applications of Phosphorus Nanomaterials

Ultra-Long Crystalline Red Phosphorus Nanowires from Amorphous Red Phosphorus Thin Films.

Structure, Preparation and Properties of Phosphorene

Computational Design of 2D Phosphorus Nanostructures for Renewable Energy Applications: A Review

Semiconducting Black Phosphorus: Synthesis, Transport Properties and Electronic Applications

Renaissance of elemental phosphorus materials: properties, synthesis, and applications in sustainable energy and environment

A Perspective on Recent Advances in Phosphorene Functionalization and its Application in Devices

Applications of Phosphorene and Black Phosphorus in Energy Conversion and Storage Devices

A Near Infrared-Activated Photocatalyst Based on Elemental Phosphorus by Chemical Vapor Deposition

Synthesis and Properties of Phosphorus Nanostructures on Au(110).

Elemental Phosphorus for Recent Sustainable Processes: Rules and Strategies in Preparation and Applications

Black Phosphorus Rediscovered: From Bulk Material to Monolayers

Phosphorene: Synthesis, Scale-Up, and Quantitative Optical Spectroscopy

From phosphorus to phosphorene: Applications in disease theranostics

Phosphorene: Synthesis, Structure, Properties and Device Applications

Encapsulation and Polymerization of White Phosphorus Inside Single-Wall Carbon Nanotubes.

Preparation and Characterization of Black Phosphorus

The rising star of 2D black phosphorus beyond graphene: synthesis, properties and electronic applications

Recent Advances in Phosphorene: Structure, Synthesis, and Properties

Black Phosphorus: Degradation Mechanism, Passivation Method, and Application for in Situ Tissue Regeneration