Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Aluminum alloys feature impressive levels of strength, ductility, castability, wear resistance, and corrosion resistance, making them highly advantageous for the aviation and automotive industries. This study investigates the dry wear performance of hybrid nanocomposites (HNCs) produced using Al6061 as the matrix, with nano-fly ash (FA) and nano-yttrium oxide (Y2O3) as reinforcing agents, utilizing the stir-casting method. The weight percentage (wt-%) of FA was fixed at 4 wt-%, while the Y2O3 varied from 1 wt-% to 3 wt-%. The specimens were prepared following ASTM-G99 standards and tested using a pin-on-disc apparatus with an E31 steel disc under four different loads: 10 N, 20 N, 30 N, and 40 N. It has been observed that wear rate has been increased with the increase in the applied load. The maximum wear rate has been recorded for the base Al6061 alloy as 5.63 × 10−4 mm3/N-m at 40 N load due to its lower wear resistance and less hardness value. The addition of reinforcement particles in the base alloy results in the grain refinement and improvement in the load-bearing capacity. It has been found that at 40 N load, the Al-6061 alloy reinforced with (4 wt-% FA + 3 wt-% Y2O3) is 56.83% superior in terms of wear resistance (2.43 × 10−4 mm3/N-m) as compared to Al6061 base alloy. The hybrid nano-composite containing 4 wt-% FA + 3 wt-% Y2O3 showed the highest value of microhardness as 123.2 HV, which is 136% higher than that of base alloy due to the higher load-bearing characteristics of the reinforcement particles. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) have been employed to analyze both unworn and worn surfaces, revealing uniform dispersion of reinforcement particles, the formation of an oxide layer, micro-pitting, wear debris, and material delamination. Grain refinement has been examined using the line intercept method (ASTM E1382-97), and X-ray diffraction (XRD) confirmed the elemental composition of the nano-reinforcements.

Slurry Erosive Wear Behavior of Hot Extruded Al6061-Si<sub>3</sub>N<sub>4</sub> Composite

Slurry Erosive Wear Behavior of Hot Extruded Al6061-Si3n4 Composite

Tribological Behaviour of Hot Extruded Al6061-Si3n4 Composite

Dry Sliding-Friction and Wear Behavior of Hot-Extruded Al6061/Si3N4/Cf Hybrid Metal Matrix Composite

Effect of Nanoaluminium Nitride Ceramic Particles on Microstructure, Mechanical Wear, and Machining Behavior of Al-Si-Mg Alloy Matrix Composites Produced by Bottom Pouring Type Stir Casting Route

Metallographic Study and Sliding Wear Optimization of Nano Si<sub>3</sub>N<sub>4</sub> Reinforced High-Strength Al Metal Matrix Composites

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

Air Jet Erosion Wear Behavior of Al6061-SiC-Carbon Fibre Hybrid Composite

Dry Sliding Wear And Static Immersion Corrosion Resistance of Aluminum Alloy 6061-T6/SiCp Metal Matrix Composite Prepared Via Friction Stir Processing

Experimental investigation in enhancing the mechanical, wear and corrosion resistance properties of Al6061-SiC-NSA composites fabricated using stir casting process.

Influence of silicon nitride (Si3N4) reinforcement on mechanical properties and wear behaviour of AZ31–Nano alumina (Al2O3) composites developed through the stir casting route

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Dry sliding wear characteristics of hybrid aluminum alloy with nano-fly ash and nano-yttrium oxide

Enhancing Wear Resistance in Al-7075 Composites Through Conventional Mixing and Casting Techniques

Study of Wear Behavior on AA6061 Reinforced with Hybrid Ceramic Composites through Optimization

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Slurry Erosion Resistance of Microwave Derived Ni-SiC Composite Claddings

Microstructural, mechanical, and wear properties of ultrasonic assisted stir casted A356 Alloy/AlN composite

Experimental Investigations on Microstructure, Mechanical and Wear Behavior Under Dry Sliding of Al6061 with Particulate-Reinforced SiC and TiB2 Metal Matrix Composite Developed by Stir Casting

Influence of AlN particles on microstructure, mechanical and tribological behaviour in AA6351 aluminum alloy