Rehydrogenation of Dehydrogenated NaAlH4 at Low Temperature and Pressure

Dalin Sun,Sesha S. Srinivasan,Tetsu Kiyobayashi,Nobuhiro Kuriyama,Craig M. Jensen

DOI: https://doi.org/10.1002/chin.200352020

2003-01-01

ChemInform

Abstract:AbstractFor Abstract see ChemInform Abstract in Full Text.

What problem does this paper attempt to address?

Rehydrogenation of Dehydrogenated NaAlH4at Low Temperature and Pressure

Dalin Sun,Sesha S. Srinivasan,Tetsu Kiyobayashi,Nobuhiro Kuriyama,Craig M. Jensen

DOI: https://doi.org/10.1021/jp030637f

2003-01-01

Abstract:NaAlH4 is considered as a promising material for onboard storage of hydrogen. It is generally thought that high temperature (> 120 degreesC) and high pressure (> 15 MPa) are needed for rehydrogenation of dehydrogenated NaAlH4. However, for practical application, reducing the rehydrogenation temperature and pressure as much as possible would be highly desirable. We have found that the dehydrogenated NaAlH4, in either the undoped or titanium-doped state, can be rehydrogenated at temperatures of 25-120 degreesC and pressures of 2-12 MPa. This finding is confirmed by the subsequent dehydrogenation at 160 degreesC. In addition to that, after rehydrogenation under the same conditions, the amount of evolved hydrogen from the titanium-doped NaAlH4 was much higher than that of the undoped NaAlH4. This clearly indicates that the addition of titanium species enhances kinetically not only the dehydrogenation, but also the reverse process, the rehydrogenation reaction of the dehydrogenated NaAlH4.
Rehydrogenation and cycling studies of dehydrogenated NaAlH4

Dalin Sun,Sesha S Srinivasan,Guorong Chen,Craig M Jensen

DOI: https://doi.org/10.1016/j.jallcom.2003.10.043

IF: 6.2

2004-01-01

Journal of Alloys and Compounds

Abstract:The hydrogenation reaction of NaH+1/3Al+1/2H2↔1/3Na3AlH6+2/3Al+H2↔NaAlH4 was studied in the temperature range of 80–170°C and the pressure range of 8–12MPa. It was found that under the pressure of 12MPa, an increase in the hydrogenation temperature from 100 to 170°C causes a reduction in the amount of absorbed hydrogen. Under the constant pressure of 10MPa, the initial rate of hydrogenation increases when the temperature increases from 80 to 120°C, and reaches an optimum at 120°C; further increase in temperature leads to a decrease in the rate. It was also observed that at a constant temperature, the rate increases with the increase of applied hydrogen pressure. The cycling studies of titanium doped NaAlH4 have shown that the initial capacity was about 3.6wt.%, but after a few dehydrogenation–rehydrogenation cycles, the capacity decreases to 3.0wt.%. And this capacity was retained with no further deterioration in the following consecutive 100 cycles. However, the rates of the two-step dehydrogenation processes were found to reduce kinetically with the ongoing cycling.
Rehydrogenation of the decomposed NaAlH4

Fang Fang,Jing Zhang,Jian Zhu,Guorong Chen,Dalin Sun,Craig M. Jensen

DOI: https://doi.org/10.3321/j.issn:0412-1961.2007.01.018

IF: 1.797

2007-01-01

ACTA METALLURGICA SINICA

Abstract:In situ X-ray diffraction showed that Ti catalyst can reduce not only the dehydrogenation temperature of NaAlH4, but also that of Na3AlH6 from 250°C to 160°C. The rehydrogenation of the decomposed NaAlH4 is reversible theoretically, but the intermediate hydride, Na3AlH6, is not fully converted into NaAlH4 because of the physical separation of NaH and Al formed in the decomposition, especially the formation of the large Al crystallites. These, therefore, result in a decrease in the hydrogen storage capacity as observed in the following cycling. Additional measurements have showed that those Al crystallites larger than 2.3 μm are no longer effective for rehydrogenation.
De-/re-hydrogenation Property of NaAlH4 Confined by Ordered Mesoporous Sphere Arrays

Wangyang WU,Fang FANG,Dalin SUN

DOI: https://doi.org/10.15943/j.cnki.fdxb-jns.2018.01.003

2018-01-01

Abstract:A nanoconfinement system(NaAlH4/MCSA) with NaAlH4 exclusively embedded in ordered mesoporous carbon sphere arrays(MCSA) was synthesized and its kinetics,thermodynamics,cycling stability was investigated.It was demonstrated that the dehydrogenation temperature of NaAlH4/MCSA system was 150 ℃ while the temperature of dehydrogenation for pristine NaAlH4 was above 230 ℃,and dehydrogenation was accomplished at 220 ℃ with 4.9％ hydrogen release.In addition,this system also showed remarkable kinetic performance for 5.1％ hydrogen that was released in 50 min at 180 ℃,while the value of pristine NaAlH4 is only 0.5％.An enhanced cycling stability was also achieved by the high-capacity retention of ＞90％ after 15 de-/re-hydrogenation cycles compared to reversible capacity ＜50％ after 5 cycles for pristine NaAlH4.This remarkable improvement for kinetics,thermodynamics and cycling stability was attributed to the synergistic effects of both nanoeonfinement and chemical catalysis.
De-/re-hydrogenation Features of NaAlH4 Confined Exclusively in Nanopores

Y. Li,G. Zhou,F. Fang,X. Yu,Q. Zhang,L. Ouyang,M. Zhu,D. Sun

DOI: https://doi.org/10.1016/j.actamat.2010.11.049

IF: 9.4

2010-01-01

Acta Materialia

Abstract:In the present work, a nanoconfinement system with NaAlH4 exclusively embedded in ordered mesoporous carbon (MC) was synthesized by a three-step procedure, i.e., thermal melting impregnation plus de-/re-hydrogenation. It is demonstrated that the NaAlH4 inside MC shows faster kinetics for dehydrogenation than the kinetics of pristine NaAlH4 with a reduction in activation energy by ∼70kJmol−1. An enhanced cycling stability is also achieved by the high-capacity retention of >80% after 15 de-/re-hydrogenation cycles. These remarkable improvements are attributed to the synergistic effects of both nanoconfinement and chemical catalysis caused by the MC, where nanoconfinement plays a dominant role. Furthermore, kinetic modeling studies suggest that the hydrogen release from the confined NaAlH4 system is governed by two processes: the initial process can be expressed by one-dimensional nucleation and growth, and the second process is jointly controlled by three-dimensional diffusion and phase boundary migration.
Hydrogen Storage Properties of Space-Confined Naalh4 Nanoparticles in Ordered Mesoporous Silica

Shiyou Zheng,Fang,Guangyou Zhou,Guoron Chen,Liuzhang Ouyang,Min Zhu,Dalin Sun

DOI: https://doi.org/10.1021/cm8002063

IF: 10.508

2008-01-01

Chemistry of Materials

Abstract:A method that is used by space-confining NaAlH4 into the as-synthesized ordered mesoporous silica (OMS) is presented in the present work. NaAlH4 in the pores of OMS is obtained by impregnation and drying techniques. It has been found that the space-confined NaAlH4 in the pores of OMS shows the lower temperature and faster kinetics for dehydrogenation than that of the pristine NaAlH4. Moreover, in the absence of a catalyst, the rehydrogenation in a dehydrogenated NaAlH4 system with nanoscale particles and phases can be achieved even with the temperatures of 125-150 degrees C and the hydrogen pressures of 3.5-5.5 MPa. The physical limitation of the NaAlH4 particles, as well as the resulting Al and NaH phases, to be nanoscale in size by the pores of OMS is believed to be responsible for these.
Dehydrogenation of a Combined LiAlH4/LiNH2System

Jun Lu,Zhigang Zak Fang

DOI: https://doi.org/10.1021/jp053954q

2005-01-01

Abstract:Although there have been numerous materials systems studied as potential candidates for hydrogen storage applications, none of the materials known to date has demonstrated enough hydrogen capacity or efficiency at required operating temperature ranges. There are still considerable opportunities for discovery of new materials or material systems that could lead to advances in science as well as commercial technologies in this area. LiAlH4 is one of the most promising materials owing to its high hydrogen content. In the present work, we investigated dehydrogenation properties of the combined system of LiAlH4 and LiNH2 under atmospheric argon. Thermogravimetric analysis (TGA) of 2LiAlH(4)/LiNH2 mixtures without any catalysts indicated that a large amount of hydrogen (similar to 8.1 wt %) can be released between 85 and 320 degrees C under a heating rate of 2 degrees C/min in three dehydrogenation reaction steps. It is found that LiNH2 effectively destabilizes LiAlH4 by reacting with LiH during the dehydrogenation process of LiAlH4.
Influence of Temperature and Hydrogen Pressure on the Hydriding/dehydriding Behavior of Ti-doped Sodium Aluminum Hydride

Xuezhang Xiao,Lixin Chen,Xinhua Wang,Shouquan Li,Qidong Wang,Changpin Chen

DOI: https://doi.org/10.1016/j.ijhydene.2007.05.015

IF: 7.2

2007-01-01

International Journal of Hydrogen Energy

Abstract:A Ti-doped sodium aluminum hydride was prepared by ball-milling NaH/Al mixture with 10mol% Ti powder under hydrogen for 12h. The hydriding/dehydriding behaviors of the ball-milled sample under different temperatures (85–160°C) and hydrogen pressures (7.5–13.5MPa) were investigated. The results show that the hydriding/dehydriding temperature and hydrogen pressure affect the hydrogen storage behavior noticeably. During hydriding, under 13.5MPa hydrogen pressure, as the hydriding temperature increases from 85 to 140°C, the hydrogen absorption rate increases first and then decreases, and reaches the highest value at 120°C. And the hydrogen absorption rate increases with the increase of hydrogen pressure all the way from 7.5 to 13.5MPa. Moreover, the hydrogen desorption rate over the hydrogen pressure of 0.1MPa increases noticeably with increasing dehydriding temperature. On cycling, the hydriding/dehydriding capacity increases first and then decreases, reaching a maximum value at the fourth cycle. X-ray diffraction (XRD) analyses show that the hydrogen storage process of the system is governed by the slow reaction kinetics and incomplete reaction of Na3AlH6 in the hydriding/dehydriding processes.
Preparation and hydrogen storage properties of space-confined NaAlH4 nanoparticles

Shiyou Zheng,Dalin Sun

2008-01-01

Abstract:A novel strategy that is by space-confining NaAlH4 into the as-synthesized ordered mesoporous silica SBA-15 is presented in the present work. NaAlH4 particles in the pores of silica were obtained by impregnation and drying techniques. The structures and micrographs of the materials were characterized by XRD, SEM and HRTEM techniques. It has been found that the space-confined NaAlH4 in the pores of SBA-15 shows the lower temperature and faster kinetics for dehydrogenation than that of the pristine NaAlH4. Moreover, in the absence of a catalyst, the re-hydrogenation in a dehydrogenated NaAlH4 system with nanoscale can be achieved even under the temperatures of 150°C. The physical limitation of the NaAlH4 particles, as well as the resulting Al and NaH phases, to be nanoscale by the pores of SBA-15 is believed to be responsible for these. This method of space-confining nanoparticles may provide an approach to improve the hydrogen storage properties, in particular, the cycling stability of NaAlH4 and other complex hydrides.
Dehydrogenation of a combined LiAlH4/LiNH2 system.

Jun Lu,Zhigang Zak Fang

DOI: https://doi.org/10.1002/chin.200606014

2005-01-01

Abstract:Although there have been numerous materials systems studied as potential candidates for hydrogen storage applications, none of the materials known to date has demonstrated enough hydrogen capacity or efficiency at required operating temperature ranges. There are still considerable opportunities for discovery of new materials or material systems that could lead to advances in science as well as commercial technologies in this area. LiAlH(4) is one of the most promising materials owing to its high hydrogen content. In the present work, we investigated dehydrogenation properties of the combined system of LiAlH(4) and LiNH(2) under atmospheric argon. Thermogravimetric analysis (TGA) of 2LiAlH(4)/LiNH(2) mixtures without any catalysts indicated that a large amount of hydrogen (approximately 8.1 wt %) can be released between 85 and 320 degrees C under a heating rate of 2 degrees C/min in three dehydrogenation reaction steps. It is found that LiNH(2) effectively destabilizes LiAlH(4) by reacting with LiH during the dehydrogenation process of LiAlH(4).
Thermodynamics, Kinetics and Modeling Investigation on the Dehydrogenation of CeAl4-doped NaAlH4 Hydrogen Storage Material

Xiulin Fan,Xuezhang Xiao,Lixin Chen,Leyuan Han,Shouquan Li,Hongwei Ge,Qidong Wang

DOI: https://doi.org/10.1021/jp208576v

2011-01-01

The Journal of Physical Chemistry C

Abstract:The CeAl4-doped NaAlH4 has been synthesized by mechanical milling NaH/Al mixture with 4 mol % CeAl4 as catalyst under hydrogen pressure of 3 MPa. The hydrogen desorption thermodynamics and kinetics of as-synthesized NaAlH4 were systematically investigated. The enthalpies for the first and second dehydrogenation steps of CeAl4-doped NaAlH4 system are estimated to be 40.56 +/- 1.62 and 51.48 +/- 1.92 kJ/mol H-2, respectively. By regulating the desorption temperatures, the two dehydrogenation steps were studied separately under a constant hydrogen backpressure of 0.1 MPa. The apparent activation energy, E-a, for the first and second step is estimated to be 87.9 and 103.6 kJ/mol, respectively, by using Arrhenius equation. Isothermal dehydrogenation measurements show that no induction period is observed in the first step or the second step under the measuring conditions. Both of the decomposition steps conform to the Johnson-Mehl-Avrami (JMA) formalism with Avrami exponent n approximate to 1, indicating that the nucleation of decomposition process is of the site saturation type. Detailed modeling study presents that the first-step dehydrogenation kinetics is most likely controlled by the reaction at a moving boundary, whereas the second-step decomposition follows the first-order reaction mechanism. Change in the dehydrogenation temperature does not alter the nature of decomposition mechanism.
Improved Dehydrogenation Performance of NaAlH4 Using NiFe2O4 Nanoparticles

Yihui Huang,Ping Li,Qi Wan,Jun Zhang,Yang Li,Ruiwen Li,Xiaoping Dong,Xuanhui Qu

DOI: https://doi.org/10.1016/j.jallcom.2017.03.182

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:The dehydrogenation properties of commercial NaAlH4 ball milled with a NiFe2O4 nanoparticle catalyst have rarely been studied. In this work, temperature programmed desorption analysis indicates that the onset temperature of three dehydrogenation steps of NaAIH(4) + 3 mol% NiFe2O4 is 72,132 and 82 degrees C lower than those of as-milled NaAlH4, respectively. The dehydrogenation capacity of NaAIH4 could be significantly improved by adding NiFe2O4. Furthermore, NaAIH(4) + 3 mol% NiFe2O4 displays good cycle stability at 150 degrees C and only a slight capacity loss after five cycles. The apparent activation energies of NaAIH(4) + 3 mol% NiFe2O4 for the three dehydrogenation steps are 54.3, 73.1 and 113.1 kJ mol(-1), respectively, as determined by differential scanning calorimetry and Kissinger analysis. From the analysis of X-ray diffraction, the new phases after dehydrogenation are NaFeO2 and Al3Ni. The reaction between NiFe2O4 and NaAIH(4) during desorption is revealed. (C) 2017 Elsevier B.V. All rights reserved.
Superior Dehydrogenation Performance of Α‐alh3 Catalyzed by Li3N: Realizing 8.0 Wt.% Capacity at 100 °C

Shaolei Zhao,Long Liang,Baozhong Liu,Limin Wang,Fei Liang

DOI: https://doi.org/10.1002/smll.202107983

IF: 13.3

2022-01-01

Small

Abstract:The high dehydrogenation temperature of aluminum hydride (AlH3) has always been an obstacle to its application as a portable hydrogen source. To solve this problem, lithium nitride is introduced into the aluminum hydride system as a catalyst to optimize the dehydrogenation drastically, which reduces the initial dehydrogenation temperature from 140.0 to 66.8 degrees C, and provides a stable hydrogen capacity of 8.24, 6.18, and 5.75 wt.% at 100, 90, and 80 degrees C within 120 min by adjusting the mass fraction of lithium nitride. Approximately 8.0 wt.% hydrogen can be released within 15 min at 100 degrees C for the sample of 10 wt.% doping. Moderate dehydrogenation temperature slows down the inevitable self-dehydrogenation process during the ball-milling process, and the enhanced kinetics at lower temperature shows the possibility of application in the fuel cell.
Dehydrogenation process of titanium and zirconium doped alanates

T Kiyobayashi,T Akita,SS Srinivasan,D Sun,S Sangawa,HT Takeshita,CM Jensen,N Kuriyama

2004-01-01

Abstract:Dehydrogenation process of Ti and Zr doped alanates was studied by means of the thermal gravimetry-differential thermal analysis (TC-DTA) and isothermal dehydrogenation kinetics measurement. With using transmission electron microscope (TEM) equipped with an electron energy loss spectrometer (EELS), we observed the distribution of Ti element on a particle of the Ti doped material. The kinetic measurement showed that: (i) Dehydrogenation of Na3AlH6 proceeds much slower than that of NaAlH4, when the former is observed as a second step of the two step consecutive dehydrogenation of Ti doped NaAlH4. (ii) But if Na3AlH6 is doped directly with Ti, the dehydrogenation rate matches that of NaAlH4. (iii) The activation enthalpies of both Ti doped NaAlH4 and Na3AlH6 are 100 kJ(.)mol(-1), and those of both Zr doped NaAlH4 and Na3AlH6 are 135 kJ(.)mol(-1). These findings imply that the rate determinig step is not related to the cleavage of Al-H bonding, which must be sensitive to whether the species involved is [AlH4](-) or [AlH6](3-), but to a long range phenomenon, such as the diffusion of the atom in the particle. The TEM-EELS observation showed that the Ti element was distributed on the surface of the particle of doped material.
Wet Chemical Synthesis of Non-solvated Rod-Like Α'-Alh3 As a Hydrogen Storage Material.

Haizhen Liu,Hongyu Ma,Longfei Zhang,Shichao Gao,Xinhua Wang,Li Xu,Shuangyu Liu,Xiantun Huang,Chenglin Lu,Hui Luo,Hua Ning,Zhiqiang Lan,Jin Guo

DOI: https://doi.org/10.3389/fchem.2019.00892

IF: 5.5

2020-01-01

Frontiers in Chemistry

Abstract:Aluminum hydride (AlH3) is a promising candidate for hydrogen storage due to its high hydrogen density of 10 wt%. Several polymorphs of AlH3 (e.g., alpha, beta, and gamma) have been successfully synthesized by wet chemical reaction of LiAlH4 and AlCl3 in ether solution followed by desolvation. However, the synthesis process of alpha'-AlH3 from wet chemicals still remains unclear. In the present work, alpha'-AlH3 was synthesized first by the formation of the etherate AlH3 through a reaction of LiAlH4 and AlCl3 in ether solution. Then, the etherate AlH3 was heated at 60 degrees C under an ether gas atmosphere and in the presence of excess LiAlH4 to remove the ether ligand. Finally, alpha'-AlH3 was obtained by ether washing to remove the excess LiAlH4. It is suggested that the desolvation of the etherate AlH3 under an ether gas atmosphere is essential for the formation of alpha'-AlH3 from the etherate AlH3. The as-synthesized alpha'-AlH3 takes the form of rod-like particles and can release 7.7 wt% hydrogen in the temperature range 120-200 degrees C.
Hydrogen Storage with Aluminum Formate, ALF: Experimental, Computational, and Technoeconomic Studies

Hayden A. Evans,Taner Yildirim,Peng Peng,Yongqiang Cheng,Zeyu Deng,Qiang Zhang,Dinesh Mullangi,Dan Zhao,Pieremanuele Canepa,Hanna M. Breunig,Anthony K. Cheetham,Craig M. Brown

DOI: https://doi.org/10.1021/jacs.3c08037

IF: 15

2023-09-29

Journal of the American Chemical Society

Abstract:Long-duration storage of hydrogen is necessary for coupling renewable H(2) with stationary fuel cell power applications. In this work, aluminum formate (ALF), which adopts the ReO(3)-type structure, is shown to have remarkable H(2) storage performance at non-cryogenic (>120 K) temperatures and low pressures. The most promising performance of ALF is found between 120 K and 160 K and at 10 bar to 20 bar. The study illustrates H(2) adsorption performance of ALF over the 77 K to 296 K temperature...

chemistry, multidisciplinary
Formation Reactions and the Thermodynamics and Kinetics of Dehydrogenation Reaction of Mixed Alanate Na2LiAlH6

Fenghuai Wang,Yongfeng Liu,Mingxia Gao,Kun Luo,Hongge Pan,Qidong Wang

DOI: https://doi.org/10.1021/jp9011697

2009-01-01

Abstract:Na2LiAlH6 was synthesized by ball-milling a mixture of NaH and LiAlH4 at a molar ratio of 2:1. NaH and LiAlH4 were readily converted in the initial ball-milling process to LiH and NaAlH4, which subsequently reacted with the remaining, excessive NaH to form Na2LiAlH6. The thermodynamic and kinetic mechanisms of dehydrogenation of Na2LiAlH6 were systematically elucidated. Approximately 6.7 wt % of hydrogen was found stored reversibly in Na2LiAlH6 through a few sequential reactions. An enthalpy change of 63.8 kJ/mol-H-2 and an apparent activation energy of about 173 kJ/mol were determined for the first-step hydrogen storage reaction, indicating the reaction was thermodynamically relatively stable with a high kinetic barrier for the decomposition of Na2LiAlH6. In depth kinetic investigations showed that the first-step dehydrogenation reaction of Na2LiAlH6 could be well interpreted with a nucleation and growth model, and its reaction rate was controlled by the diffusion of substance. The dehydrogenation mechanism developed in this work can be helpful for further efforts on the improvement of the hydrogenation/dehydrogenation performances of Na2LiAlH6.
Synthesis and Hydriding/dehydriding Properties of Nanosized Sodium Alanates Prepared by Reactive Ball-Milling

Xuezhang Xiao,Kairong Yu,Xiulin Fan,Zhe Wu,Xinhua Wang,Changpin Chen,Qidong Wang,Lixin Chen

DOI: https://doi.org/10.1016/j.ijhydene.2010.10.012

IF: 7.2

2011-01-01

International Journal of Hydrogen Energy

Abstract:TiF3-doped NaH/Al mixture was hydrogenated into Na3AlH6 and NaAlH4 complex hydrides by reactive ball-milling at room temperature through the optimization of milling duration and hydrogen pressure. The analysis of the preparation of NaAlH4 samples during reactive ball-milling process has been performed by XRD and TG/DSC. It has been found that Na3AlH6 was formed under 0.5 MPa hydrogen pressure and 30 h milling duration, while NaAlH4 was formed under 0.8 MPa hydrogen pressure and 45 h milling duration. The process of preparing NaAlH4 by ball-milling was found accomplished via two reaction steps, namely: (1) NaH + Al + H-2 Na3AlH6 and (2) Na3AlH6 + Al + H-2 -> NaAlH4. As the hydrogen pressure and milling duration increase, the synthetic yield of NaAlH4 and its corresponding dehydriding capacity are both increased. With increased hydrogen pressure (0.8-3 MPa) and milling duration (45-60 h), the cell volume of Na3AlH6 decreases while that of NaAlH4 increases gradually. The abundance of Na3AlH6 phase decreases from 57.76 (x = 0.8, y = 45) to 8.69 wt.% (x = 3, y = 60), and the abundance of NaAlH4 phase increases from 20.63 (x = 0.8, y = 45) to 86.50 wt.% (x = 3, y = 60). All the samples prepared in this way have fairly good activation behavior and fast hydriding/dehydriding reaction kinetics, which are capable of absorbing 4.26 wt.% hydrogen at 120 degrees C and desorbing 4.12 wt.% hydrogen at 150 degrees C, respectively. The improvement of hydriding/dehydriding properties is ascribed to the favorable microstructure and ultrafine particle features of nanosized NaAlH4 formed during ball-milling at the optimum synthetic condition. (C) 2010 Professor T. Nejat Veziroglu. Published by Elsevier Ltd. All rights reserved.
Achieving ambient temperature hydrogen storage in ultrafine nanocrystalline TiO2@C-doped NaAlH4

yongfeng liu,xin zhang,ke wang,yaxiong yang,mingxia gao,hongge pan

DOI: https://doi.org/10.1039/c5ta09400c

IF: 11.9

2016-01-01

Journal of Materials Chemistry A

Abstract:Sodium alanate (NaAlH4) has attracted tremendous interest as a prototypical high-density complex hydride for on-board hydrogen storage. However, poor reversibility and slow kinetics limit its practical application. In this paper, we propose a novel strategy for the preparation of an ultrafine nanocrystalline TiO2@C-doped NaAlH4 system by first calcining the furfuryl alcohol-filled MIL-125(Ti) at 900 degrees C and then ball milling with NaAlH4 followed by a low-temperature activation process at 150 degrees C under 100 bar H-2. The as-prepared NaAlH4-9 wt% TiO2@C sample releases hydrogen starting from 63 degrees C and re-absorbs starting from 31 degrees C, which are reduced by 114 degrees C and 54 degrees C relative to those of pristine NaAlH4, respectively. At 140 degrees C, approximately 4.2 wt% of hydrogen is released within 10 min, representing the fastest dehydrogenation kinetics of any presently known NaAlH4 system. More importantly, the dehydrogenated sample can be fully hydrogenated under 100 bar H-2 even at temperatures as low as 50 degrees C, thus achieving ambient-temperature hydrogen storage. The synergetic effect of the Al-Ti active species and carbon contributes to the significantly reduced operating temperatures and enhanced kinetics.
The Effect of Heating Rate on the Reversible Hydrogen Storage Based on Reactions of Li3alh6 with Linh2

Jun Lu,Zhigang Zak Fang,Young Joon Choi,Hong Yong Sohn,Chul Kim,Robert C. Bowman,Son-Jong Hwang

DOI: https://doi.org/10.1016/j.jpowsour.2008.07.040

IF: 9.2

2008-01-01

Journal of Power Sources

Abstract:Reversible dehydrogenation and hydrogenation reactions have been reported for a number of reactions based on lithium alanate and lithium amide materials. The dehydrogenation and hydrogenation reactions involving these materials are, however, usually very complex. Significant discrepancies exist among different studies published in literature. Understanding the reaction mechanism and the dependence of the reaction pathway on material preparation processes and processing parameters is critical. In this paper, the hydrogenation reactions of the mixture of 3Li2NH/Al/4wt%TiCl3 were investigated as a function of the heating rate. The hydrogenated products were characterized by means of TGA, XRD and solid-state NMR. These new results showed that the re-formation of Li3AlH6 depends strongly on the heating rate during the hydrogenation process. The dehydrogenation and rehydrogenation reaction pathways and possible mechanisms of the combined system are, however, still under investigation.

Rehydrogenation of Dehydrogenated NaAlH4 at Low Temperature and Pressure

Rehydrogenation of Dehydrogenated NaAlH<sub>4</sub>at Low Temperature and Pressure

Rehydrogenation and cycling studies of dehydrogenated NaAlH4

Rehydrogenation of the decomposed NaAlH4

De-/re-hydrogenation Property of NaAlH4 Confined by Ordered Mesoporous Sphere Arrays

De-/re-hydrogenation Features of NaAlH4 Confined Exclusively in Nanopores

Hydrogen Storage Properties of Space-Confined Naalh4 Nanoparticles in Ordered Mesoporous Silica

Dehydrogenation of a Combined LiAlH<sub>4</sub>/LiNH<sub>2</sub>System

Influence of Temperature and Hydrogen Pressure on the Hydriding/dehydriding Behavior of Ti-doped Sodium Aluminum Hydride

Preparation and hydrogen storage properties of space-confined NaAlH4 nanoparticles

Dehydrogenation of a combined LiAlH4/LiNH2 system.

Thermodynamics, Kinetics and Modeling Investigation on the Dehydrogenation of CeAl4-doped NaAlH4 Hydrogen Storage Material

Improved Dehydrogenation Performance of NaAlH4 Using NiFe2O4 Nanoparticles

Superior Dehydrogenation Performance of Α‐alh3 Catalyzed by Li3N: Realizing 8.0 Wt.% Capacity at 100 °C

Dehydrogenation process of titanium and zirconium doped alanates

Wet Chemical Synthesis of Non-solvated Rod-Like Α'-Alh3 As a Hydrogen Storage Material.

Hydrogen Storage with Aluminum Formate, ALF: Experimental, Computational, and Technoeconomic Studies

Formation Reactions and the Thermodynamics and Kinetics of Dehydrogenation Reaction of Mixed Alanate Na<sub>2</sub>LiAlH<sub>6</sub>

Synthesis and Hydriding/dehydriding Properties of Nanosized Sodium Alanates Prepared by Reactive Ball-Milling

Achieving ambient temperature hydrogen storage in ultrafine nanocrystalline TiO2@C-doped NaAlH4

The Effect of Heating Rate on the Reversible Hydrogen Storage Based on Reactions of Li3alh6 with Linh2