Abstract:In the present paper, the effects of thermal insulation cover curing on the rise in temperature of concrete, and further on the mechanical properties of the concrete are measured experimentally. In the experiments, polyurethane foam boards of 100 mm thickness were used for thermal insulation, and three concrete strength grades of C30, C50 and C80, were used as concrete samples. Conventional standard curing, and two heat curing methods with a constant temperature of 40 °C and 60 °C were used for comparison. The pore structure of the cement paste subject to the different curing procedures, including insulation cover curing, heat curing and standard curing, was experimentally measured using mercury intrusion porosimetry. The test results show that rate of increase in compressive strength compared with standard curing is 22–34%, 16–26%, and 23–67%, respectively, for C30, C50, C80 concrete after being subject to 1 to 3 days thermal insulation cover curing in the initial period after concrete casting. As expected, initial heat curing of concrete will result in a reduction in the long-term strength of the concrete. At 28 days, the strength reduction rate compared with standard curing due to the insulation cover curing is 3.1–5.9%, 0.6–3.0%, 0–3.2%, respectively, for C30, C50, C80 concrete. By contrast, the compressive strength reduction compared with standard curing at 28 days is 8.6–10.5%, 8.6–9.1%, 4.7–5.6%, respectively, for C30, C50, C80 concrete after being subject to a constant heat curing of 40 °C and 60 °C in the initial period after concrete casting. Measurement of the pore structure of the paste subject to different curing procedures initially after casting shows that rising curing temperature leads to coarser pores, especially an increase in capillary pore fraction. Among the four curing methods used in the present study, the effect of insulation cover curing and low temperature (40 °C) heat curing on the capillary pore content is small, while the effect of high temperature (60 °C) heat curing is significant.

Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete

Experimental study on dynamic behavior of concrete at elevated temperatures

Effect of the Curing Condition and High-Temperature Exposure on Ground-Granulated Blast-Furnace Slag Cement Concrete

Effect of the Thermal Insulation Cover Curing on Temperature Rise and Early-Age Strength of Concrete

Effect of Curing Conditions on Property of High Performance Concrete with Composite Mineral Admixture

Use of Cement Hydration Heat As Heating Resource in Curing of Precast Concrete - Temperature Rise Simulation

Study on Shear Behavior of Concrete-polymer Cement Mortar at Elevated Temperature

Evaluate the effect of coarse aggregates on cement hydration heat and concrete temperature modelling using isothermal calorimetry

Experiment and Analysis of Concrete Adiabatic Temperature Rise

Effects of Curing Temperature on Expansion of Concrete Due to ASR

Cement Hydration Rate of Ordinarily and Internally Cured Concretes

Effects of Elevated Temperature on the Residual Behavior of Concrete Containing Marble Dust and Foundry Sand

Effects of Mixing and Curing Temperature on the Strength Development and Pore Structure of Fly Ash Blended Mass Concrete

Effect of cenospheres on the proprieties of plain concrete exposed to elevated temperature

Performance of Different Concrete Types Exposed to Elevated Temperatures: A Review

Effect of High-Temperature Curing Methods on the Compressive Strength Development of Concrete Containing High Volumes of Ground Granulated Blast-Furnace Slag

Modelling on Temperature Field of High-Strength Concrete Pavement with the Impact of Internal Curing

Hydration Mechanism and Mechanical-Thermal Correlation of Cemented Paste Backfill under Different Curing Temperatures

Experimental Study of Thermal-Hydraulic-Mechanical Coupling Behavior of High-Performance Concrete

Influence of Binder Types and Temperatures on the Mechanical Properties and Microstructure of Cemented Paste Backfill

Influence of elevated curing temperature on the properties of cement paste and concrete at the same hydration degree