Abstract:BackgroundGlaucoma is the primary cause of irreversible blindness worldwide associated with high intraocular pressure (IOP). Elevated intraocular pressure will affect the normal aqueous humor outflow, resulting in deformation of iris. However, the deformation ability of iris is closely related to its material properties. Meanwhile, the passive deformation of the iris aggravates the pupillary block and angle closure. The nature of the interaction mechanism of iris deformation and aqueous humor fluid flow has not been fully understood and has been somewhat a controversial issue. The purpose here was to study the effect of IOP, localization, and temperature on the flow of the aqueous humor and the deformation of iris interacted by aqueous humor fluid flow.MethodsBased on mechanisms of aqueous physiology and fluid dynamics, 3D model of anterior chamber (AC) was constructed with the human anatomical parameters as a reference. A 3D idealized standard geometry of anterior segment of human eye was performed. Enlarge the size of the idealization geometry model 5 times to create a simulation device by using 3D printing technology. In this paper, particle image velocimetry technology is applied to measure the characteristic of fluid outflow in different inlet velocity based on the device. Numerically calculations were made by using ANSYS 14.0 Finite Element Analysis. Compare of the velocity distributions to confirm the validity of the model. The fluid structure interaction (FSI) analysis was carried out in the valid geometry model to study the aqueous flow and iris change.ResultsIn this paper, the validity of the model is verified through computation and comparison. The results indicated that changes of gravity direction of model significantly affected the fluid dynamics parameters and the temperature distribution in anterior chamber. Increased pressure and the vertical position increase the velocity of the aqueous humor fluid flow, with the value increased of 0.015 and 0.035 mm/s. The results act on the iris showed that, gravity direction from horizontal to vertical decrease the equivalent stress in the normal IOP model, while almost invariably in the high IOP model. With the increased of the iris elasticity modulus, the equivalent strain and the total deformation of iris is decreased. The maximal value of equivalent strain of iris in high IOP model is higher than that of in normal IOP model. The maximum deformation of iris is lower in the high IOP model than in the normal IOP model.ConclusionThe valid model of idealization geometry of human eye could be helpful to study the relationship between localization, iris deformation and IOP. So far the FSI analysis was carried out in that idealization geometry model of anterior segment to study aqueous flow and iris change.

Evaluation of Flow Field in the Anterior Segment During Irrigation and Aspiration in Cataract Surgery with Three-Dimensional Computational Simulation

The aqueous humour dynamics in primary angle closure disease: a computational study.

Fluid-structure interaction in phaco-emulsification based cataract surgery

Changes in Total, Anterior, and Posterior Corneal Surface Higher-Order Aberrations after 1.8 Mm Incision and 2.8 Mm Incision Cataract Surgery

Numerical Simulation of Aqueous Flow in Laser Iridotomy

Optimization of Surgical Protocol for Laser Iridotomy Based on the Numerical Simulation of Aqueous Flow

Fluid and structure coupling analysis of the interaction between aqueous humor and iris

Early Assessment of Circumferential Anterior Segment Structures Following Implantable Collamer Lens V4c Implantation Via SS-OCT

The effect of irrigation and aspiration on the corneal endothelial cell density in patients undergoing Implantable Collamer Lens with a central hole implantation for myopia correction

Evaluation of needle movement effect on root canal irrigation using a computational fluid dynamics model

Analysis of Indicators for Assessing the Risk of Progression from PACS to APAC and the Degree of Intraocular Pressure Elevation in APAC Using AS-OCT

Theoretical study on the need for laser iridotomy in an implantable collamer lens with a hole using computational fluid dynamics

Optical Coherence Tomography Analysis of Anterior Segment Parameters Before and after Laser Peripheral Iridotomy in Primary Angle-Closure Suspects by Using CASIA2

Association between the site of clear corneal Phakic intraocular lens implantation incisions and the inflow of ocular surface fluid into the anterior chamber

Numerical Investigation of Irrigant Flow Characteristics in Curved Root Canals with Computational Fluid Dynamics Method

Intraoperative Posterior Chamber Irrigation to Enhance Vitreous Cavity Support During Phacoemulsification Cataract Surgery after Vitrectomy

A Mechanistic Model of Aqueous Humor Flow to Study Effects of Angle Closure on Intraocular Pressure

Assessing the clinical efficacy of phacoemulsification cataract extraction in treating acute primary angle closure and fellow primary angle closure suspect eyes using AS-OCT

An evaluation of fluid distribution at the implant site during implant placement by using a computational fluid dynamics model

Effect of Anterior Chamber Instability during Phacoemulsification Combined with Intraocular Lens Implantation

A Method of Measuring Anterior Chamber Volume Using the Anterior Segment Optical Coherence Tomographer and Specialized Software