Abstract:Despite the high theoretical specific capacity and ultralow reduction potential advantages of Li anodes, dendrite growth in Li metal batteries leads to many problems. Realizing uniform Li deposition is the key to solving these problems, but it is usually difficult for traditional Li metal electrodes. In this study, CuO nanofilm-covered Cu microcones (NFMCs) on a Cu foil are prepared as current collectors to suppress Li dendrite growth and improve the electrochemical performance of the batteries. Li2O is in situ formed during the course of Li deposition according to the conversion reaction between CuO and Li. The nucleation energy barrier of Li is decreased due to high affinity between Li2O and Li. In addition, we found that Li2O also decreases the elastic strain energy at the interface between the deposited Li and the Li2O film, leading to uniform coverage of Li metal on microcones. The Li2O/Cu NFMCs show a coral-like structure instead of the sharp cone structure in Cu microcones. Thus, they can effectively mitigate the tip-charge effect, which will cause the continuous reduction of the Li ion at the tip. As a result, uniform and stable Li deposition without observation of the Li dendrite up to 1000 cycles at a current density of 5 mA cm–2 is achieved using this Li2O/Cu NFMC substrate. A full cell upon pairing with LiFePO4 achieves a high Coulombic efficiency of 96.7% for over 100 cycles at 0.2 C with a capacity retention over 92.7%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00218.Simulation model of the (a) Cu cone and (b) Li2O/Cu NFMC (2D axisymmetric graph); SEM image of the CuO layer directly forming on the Cu foil; nucleation overpotential of Li deposited on the CuO foil; SEM images of the growth process of the 2O/Cu foil; voltage–time curves of 2O/Cu NFMCs in symmetric cells with an area capacity of 4.5 mA h cm–2 at 13 mA cm–2 (5 mA h cm–2 Li previously deposited at 2 mA cm–2); voltage–time curves of 2O/Cu NFMCs, cones, and the 2O/Cu foil in symmetric cells with an area capacity of 1 mA h cm–2 at 1, 2, and 5 mA cm–2; Coulombic efficiency of Li2O/Cu NFMC and Cu cone current collectors with an area capacity of 1 mA h cm–2 at 2 mA cm–2; Nyquist plots of the 2O/Cu foil after various cycles in a symmetric cell with an area capacity of 1 mA h cm–2 at 1 mA cm–2; cycling performance of the LFP| foil full cell at 0.2 C; XPS spectrum of 2O/Cu NFMCs after Li deposition; and TEM image of a copper cone and HRTEM image of the cone edge (PDF)This article has not yet been cited by other publications.

CuO Nanofilm-Covered Cu Microcone Coating for a Long Cycle Li Metal Anode by In Situ Formed Li 2 O

CuO Nanofilm-Covered Cu Microcone Coating for a Long Cycle Li Metal Anode by in Situ Formed Li2O

Nano-Cone Structured Lithiophilic Ni Film on Cu Current Collector Facilitates Li<SUP>+</SUP> Ion Diffusion Toward Uniform Lithium Deposition

Coupling a Three-Dimensional Nanopillar and Robust Film to Guide Li-Ion Flux for Dendrite-Free Lithium Metal Anodes

Nano‐Cone Structured Lithiophilic Ni Film on Cu Current Collector Facilitates Li + Ion Diffusion Toward Uniform Lithium Deposition

In Situ Growth of CuO Submicro-Sheets on Optimized Cu Foam to Induce Uniform Li Deposition and Stripping for Stable Li Metal Batteries

<i>In situ</i> coating of a lithiophilic interphase on a biporous Cu scaffold with vertical microchannels for dendrite-free Li metal batteries

Constructing Sn-Cu2O Lithiophilicity Nanowires As Stable and High-Performance Lithium Metal Anodes

Vertically Aligned Lithiophilic CuO Nanosheets on a Cu Collector to Stabilize Lithium Deposition for Lithium Metal Batteries

Nanoporous Cuprous Oxide/lithia Composite Anode with Capacity Increasing Characteristic and High Rate Capability

Lithiophilic Cuo Nanoflowers On Ti-Mesh Inducing Lithium Lateral Plating Enabling Stable Lithium-Metal Anodes With Ultrahigh Rates And Ultralong Cycle Life

Super‐Assembled Hierarchical CoO Nanosheets‐Cu Foam Composites as Multi‐Level Hosts for High‐Performance Lithium Metal Anodes

Flaky and Dense Lithium Deposition Enabled by a Nanoporous Copper Surface Layer on Lithium Metal Anode

Highly Lithiophilic Copper-Reinforced Scaffold Enables Stable Li Metal Anode

In-Plane Highly Dispersed Cu2O Nanoparticles for Seeded Lithium Deposition

Nano-Cu-embedded carbon for dendrite-free lithium metal anodes

Lithiophilic Ag Nanoparticle Layer on Cu Current Collector toward Stable Li Metal Anode

Stable Li/Cu2O composite anodes enabled by a 3D conductive skeleton with lithiophilic nanowire arrays

Regulating the Li Nucleation/Growth Behavior via Cu 2 O Nanowire Array and Artificial Solid Electrolyte Interphase toward Highly Stable Li Metal Anode

Lithiophilic Hyperbranched Cu Nanostructure for Stable Li Metal Anodes

Large‐Scale Modification of Commercial Copper Foil with Lithiophilic Metal Layer for Li Metal Battery