Abstract:The investigation of frictional pressure drops in wire-wrapped bundles at low flow velocities is crucial for thermal-hydraulic studies of sodium-cooled fast reactor cores. This study aims to refine empirical formulas for predicting friction factors in wire-wrapped bundles by addressing their limitations in accurately calculating friction factors during transition regime. By analyzing existing empirical formulas and meticulously observing frictional pressure drop experiments conducted under low-flow conditions that reported in the literature, the study proposes and demonstrates the mechanism of the laminar-to-transitional regime transition in wire-wrapped bundles. Additionally, experimental research was conducted on the frictional pressure drop of a 37-rod wire-wrapped bundle. A novel high-precision differential pressure measurement technique, the photographic liquid column manometer, was employed to enhance frictional pressure drop measurement accuracy. This innovative method achieves a measurement uncertainty of less than 2 Pa within a range of 0 to 300 Pa. The mass flow rate of the fluid was measured and converted to obtain the flow velocity through the assembly, further improving the accuracy of flow velocity measurements. The analysis and experiments reveal that the transition from the laminar to transitional regime does not occur uniformly but initiates locally in certain subchannels before spreading across the assembly as flow velocity increases. Significant increases in the frictional pressure drop occur only after a sufficient number of subchannels have undergone transition. This perspective is supported by extensive existing literature, which report that in assemblies with fewer rod bundles, smaller P/D and H/D values, and constructed from hard metal materials such as stainless steel, the friction factor at the initial stage of the transitional regime shows a significant increase or remains constant with increasing Reynolds number. Under these conditions, the high consistency of the P/D ratio within the assembly causes the fluid to transition within a narrow range of flow velocities, leading to a marked increase in the friction factor with Reynolds number. The research results also indicate that the prediction accuracy of the critical Reynolds number for the laminar-to-transitional flow transition significantly impacts the calculation accuracy of empirical formulas at low flow velocities. Formulas using smaller predicted values of the critical Reynolds number show better agreement between predicted values and the measured results in this study. Therefore, the study recommends adopting smaller critical Reynolds numbers and interpolation indices in empirical formulas to facilitate an early onset and smooth transition of laminar-to-transitional regime behavior in friction factors, thereby improving the accuracy of calculated friction factors.

Experimental Investigation on Pressure Drop of a PWR Fuel Assembly under Low Re Conditions

Effect of Tip Clearance on the Heat Transfer and Pressure Drop Performance in the Micro-Reactor with Micro-Pin–fin Arrays at Low Reynolds Number

Periodicity and transversal pressure distribution in a Wire‐wrapped 19‐Pin fuel assembly

An Experiment Study of Pressure Drop and Flow Distribution in Subchannels of a 37-Pin Wire-Wrapped Rod Bundle

Experimental Study on Frictional Pressure Drop Characteristics of Wire-wrapped Bundles in Transition Flow

Effect of Distribution Header Pressure Drop on Flow Distribution of Assembly for Sodium-cooled Fast Reactor

Experimental Study on Single-Phase Frictional Pressure Drop for Water Flow under High Heat Fluxes

The Development and Assessment of a New CHF Correlation for PWR Fuel Assemblies

Numerical Simulation of Pressure Drop in Fuel Channel End Fitting

Development of Analytical Models for the Natural Circulation Behavior of a Full-Scale PWR Fuel Assembly

Applicability of RANS models and pressure drop in edge subchannels for 19-pin wire-wrapped fuel bundle channel in CiADS

Modeling and Validation of RELAP5 for Natural Circulation Flow in a Single PWR Fuel Assembly

Prioritizing Pressure Drop Research in Nuclear Thermal Hydraulics

An Experimental and Numerical Study of Pressure Drop and Hydraulic Behavior in Scaled-Down Fuel Bundle

High Fidelity Core Flow Measurement Experiment for an Advanced Research Reactor Using a Real Scale Mockup

Pressure Drop in Seven-Pin Wire-Wrapped Rod Bundle for the Sodium Cartridge Loop in Versatile Test Reactor

PIV Measurement and Numerical Investigation on Flow Characteristics of Simulated Fast Reactor Fuel Subassembly

Reflooding characteristics investigation and predicted models improvement for the pressurized water reactor with the tight lattice core design

Detailed Analysis of the Particle Residence Time Distribution in a Pressurized Drop‐tube Reactor

Experimental Investigation of the Frictional Pressure Drop of Steam-Water Two-Phase Flow in AP1000 Surge Line

Experimental Study on the Natural Circulation Behavior of a Full-Scale PWR Fuel Assembly