Abstract:Large capacity supercritical boiler is at the leading edge of efficiency boost for thermal power plant. Water wall design is a key issue for a supercritical boiler. To ensure successful design and safe operation of water wall, studying hydraulic resistance of water is significant. Considerable work on frictional pressure drop of gas-liquid two-phase flow in tubes has been done and various correlations have been proposed to predict it. However, these correlations are restricted to particular rib geometries and flow conditions. Because of significant variations in thermo physical properties near the critical and pseudo-critical points, pressure drop at supercritical pressures is different from that at subcritical pressures. However, limited studies have been devoted to estimate hydraulic resistance of supercritical water. More work need be conducted to develop prediction method for pressure drop at supercritical pressures. Therefore, to accumulate fundamental experimental data for the design of a supercritical boiler, an experiment on hydraulic resistance of water was performed in a vertical upward rifled tube. The experiment was carried out in the high-temperature and high-pressure steam-water test loop at Xi'an Jiaotong University. Based on the experimental data, the two-phase frictional multiplier was calculated to analyze the two-phase frictional pressure drop. At low to moderate vapor quality, the two-phase frictional multiplier increases rapidly and reaches a peak. When the vapor quality exceeds a certain value, the two-phase frictional multiplier starts to decrease with increasing vapor quality. It is because the tube wall is covered by liquid film at low to moderate vapor quality. Within the high vapor quality region, the high-speed vapor tears the liquid film and the flow pattern turns to mist flow with lower frictional pressure drop. Increasing pressure decreases the two-phase frictional multiplier and when the pressure approaches the critical pressure, the multiplier is close to 1. The effect of mass flux on the multiplier is so weak that it can be neglected. At supercritical pressures, the pressure drops due to frictional resistance and flow acceleration both increase with bulk fluid enthalpy. Increasing pressure decreases the frictional pressure drop. This result is mainly attributed to pressure approaching the critical point. Frictional pressure drop is significantly affected by fluid property variations; in particular, severe density decreases with increasing bulk fluid enthalpy. Acceleration pressure drop increases with decreasing pressure and increasing heat flux. When heat flux increases, the density difference between the inlet and the outlet increases with the same mass flux, which results in a considerable acceleration pressure drop. Decreasing pressure results in a similar acceleration pressure drop variation because of the same reason. The frictional resistance coefficient was calculated to analyze the supercritical frictional pressure drop. In the large specific heat region, the frictional resistance coefficient peaks at a certain enthalpy in the vicinity of the pseudo-critical point, and increasing mass flux reduces the magnitude of the peak value.

Experimental Study on Single-Phase Frictional Pressure Drop for Water Flow under High Heat Fluxes

Frictional Resistance Investigation of Sco2 and a Semi-Empirical Friction Factor Correlation Based on Wall-of-the-law

Effect of Tip Clearance on the Heat Transfer and Pressure Drop Performance in the Micro-Reactor with Micro-Pin–fin Arrays at Low Reynolds Number

Pressure Drop for Highly Subcooled Water Flow Boiling under High Heat and Mass Fluxes

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Experimental Investigation on Pressure Drop of Supercritical Water in an Annular Channel

Turbulent Heat Transfer for Coolant Water Flow in Plasma Facing Component

Experimental Investigation On Heat Transfer And Frictional Characteristics Of Vertical Upward Rifled Tube In The Advanced Ultra Supercritical Steam Generator

Experimental Investigations on Pressure Drop for Subcooled Water in a Circular Channel with a Twisted Tape Insert under One-Side Heating Conditions

Experimental Investigation of the Pressure Drop and Friction Factor of Supercritical Water in a 2 × 2 Rod Bundle

Frictional Pressure Drop Correlation of Steam-Water Two-Phase Flow in Helically Coiled Tubes

Experimental investigation on pressure drop characteristics of two-phase flow in a rod bundle geometry under high pressure conditions

Hydraulic Resistance of In-Tube Cooling Supercritical Water Accompanying Out-Tube Pool Boiling

The Study of Critical Heat Flux in Upflow Boiling Vertical Round Tube under High Pressure

An Experiment Study of Pressure Drop and Flow Distribution in Subchannels of a 37-Pin Wire-Wrapped Rod Bundle

Experimental Study on Frictional Pressure Drop Characteristics of Wire-wrapped Bundles in Transition Flow

Flow thermohydraulic characterization of open diverging microchannel heat sink for high heat flux dissipation

Flow and Heat Transfer Characteristics of High-Pressure Water Flowing in A Vertical Upward Smooth Tube at Low Mass Flux Conditions

Hydraulic Resistance of Subcritical and Supercritical Water Flowing in A Rifled Tube

Predictions of Heat Transfer Coefficients and Pressure Drops to Supercritical Pressure Hcfc22 Flowing in A Small Tube

Experimental Study on Heat Transfer and Pressure Drop Characteristics in a Microchannel Heat Exchanger Assembly with S-shaped Fins