Abstract:Metallic sodium (Na) has been regarded as one of the most attractive anodes for Na-based rechargeable batteries due to its high specific capacity, low working potential, and high natural abundance. However, several important issues hinder the practical application of the metallic Na anode, including its high reactivity with electrolytes, uncontrolled dendrite growth, and poor processability. Metal nitrates are common electrolyte additives used to stabilize the solid electrolyte interphase (SEI) on Na anodes, though they typically suffer from poor solubility in electrolyte solvents. To address these issues, a Na/NaNO3 composite foil electrode was fabricated through a mechanical kneading approach, which featured uniform embedment of NaNO3 in a metallic Na matrix. During the battery cycling, NaNO3 was reduced by metallic Na sustainably, which addressed the issue of low solubility of an SEI stabilizer. Due to the supplemental effect of NaNO3, a stable SEI with NaNxOy and Na3N species was produced, which allowed fast ion transport. As a result, stable electrochemical performance for 600 h was achieved for Na/NaNO3||Na/NaNO3 symmetric cells at a current density of 0.5 mA cm–2 and an areal capacity of 0.5 mAh cm–2. A Na/NaNO3||Na3V2(PO4)2O2F cell with active metallic Na of ∼5 mAh cm–2 at the anode showed stable cycling for 180 cycles. In contrast, a Na||Na3V2(PO4)2O2F cell only displayed less than 80 cycles under the same conditions. Moreover, the processability of the Na/NaNO3 composite foil was also significantly improved due to the introduction of NaNO3, in contrast to the soft and sticky pure metallic Na. Mechanical kneading of soft alkali metals and their corresponding nitrates provides a new strategy for the utilization of anode stabilizers (besides direct addition into electrolytes) to improve their electrochemical performance.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01571?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01571</a>.Additional digital and SEM images; additional XPS results; additional CVs and Nyquist plots; additional Tables for the fitting results of the Nyquist plots; and additional voltage profiles, cycle performance, and voltage curves (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01571/suppl_file/am1c01571_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

An In-Situ Alloyed Ni-Fe Co-reaction Electrode for High-Stability and High-Rate Na-metal Halide Batteries

Nanoarray Architecture of Ultra-Lithiophilic Metal Nitrides for Stable Lithium Metal Anodes

Aluminum-doping-based Method for the Improvement of the Cycle Life of Cobalt–nickel Hydroxides for Nickel–zinc Batteries

Manipulating the Electronic Structure of Nickel via Alloying with Iron: Toward High-Kinetics Sulfur Cathode for Na–S Batteries

Designing an Al-Rich In Situ Coating for Stabilizing High-Energy-Density Li Metal Battery Electrodes via Electrolyte Modulation

Enhanced processability and electrochemical cyclability of metallic sodium at elevated temperature using sodium alloy composite

Realizing a Highly Stable Sodium Battery with Dendrite-Free Sodium Metal Composite Anodes and O3-type Cathodes

Hierarchical Co3o4 Nanofiber-Carbon Sheet Skeleton With Superior Na/Li-Philic Property Enabling Highly Stable Alkali Metal Batteries

A High‐Performance Alloy‐Based Anode Enabled by Surface and Interface Engineering for Wide‐Temperature Sodium‐Ion Batteries

Structure Distortion Induced Monoclinic Nickel Hexacyanoferrate As High‐Performance Cathode for Na‐Ion Batteries

Alloying-triggered heterogeneous nucleation for the flexible sodium metallic batteries

Stable sodium metal anode enabled by interfacial room‐temperature liquid metal engineering for high‐performance sodium–sulfur batteries with carbonate‐based electrolyte

Multifunctional High‐Entropy Alloy Nanolayer Toward Long‐Life Anode‐Free Sodium Metal Battery

Hierarchical Oα-rich Co3O4 Nanoarray Anchored on Ni Foam with Superior Lithiophilicity Enabling Ultrastable Lithium Metal Batteries

Addressing the Low Solubility of a Solid Electrolyte Interphase Stabilizer in an Electrolyte by Composite Battery Anode Design

Regulating the Uniform Na Deposition Behavior Using Atomically Dispersed Fe-Doped Mesoporous Carbon Nanospheres for High-Performance Sodium Metal Batteries

Unraveling the synergistic effects and mechanisms of nano-carbon modification on metal hydride alloys for enhanced electrochemical performance in energy storage applications

Large-scale Sodiophilic/buffered Alloy Architecture Enables Deeply Cyclable Na Metal Anodes

Advanced Fluorinated Electrolytes Supporting High-Energy Lithium Batteries with Ni-Rich Cathodes

Enabling high energy lithium metal batteries via single-crystal Ni-rich cathode material co-doping strategy

Stable Na Metal Anode Enabled by a Reinforced Multistructural SEI Layer