Abstract:Abstract Steel-aluminum composite material combine the excellent mechanical properties of steel such as high strength and good wear resistance with the advantages of lightweight aluminum for widely using in automobile engine block, gearbox and other car body structures. In this paper, a new process is used to cast the alloy steel sleeve into Al-Si alloy matrix for preparing aluminum engine block with steel cylinder liner. The process consists of three parts: the surface pre-treatment of steel, the hot-dipping melt and solid-liquid casting of steel with aluminum. Generally, the hot dipping melt should have lower melting point than the melting point of aluminum alloy, good temperature oxidation resistance and amount of solid solubility both with steel and aluminum. Giving consideration of such condition and cost, Zn ́ Al and its alloys are used in present paper for learning the effect of hot dip coating melts on the interface properties of steel/aluminum at different times. After hot dipping, a coating formed on the surface of the steel bushing, which improves its wettability in the aluminum melt and the metallurgical bonding effect of the steel-aluminum interface. The microstructure, phase composition, growth kinetics and hardness distribution of the interface were analyzed by metallographic microscopy, scanning electron microscopy with EDS. The results show that the metallurgical bonding interface of steel/aluminum bimetal casting can be obtained by hot dipping. Hard-brittle diffusion layer produced by dipping pure Al is thicker than that produced by ZL101. Dipping pure zinc produces a dense intermetallic layer of 3-5 um and a large amount of dispersed phase of Al 3 FeZn x , and the bonding performance of such interface is better than the other two. The interface hardness of steel-aluminum bimetal casting obtained by hot dipping pure Al melt, ZL101 melt and pure Zn melt can reach 563.5HV, 528.3HV and 632.3HV, respectively.

Bonding of Cast Iron-Aluminum in Bimetallic Castings by High-Pressure Die Casting Process

Achieving Metallurgical Bonding in Aluminum/Steel Bimetallic Castings

An Investigation into Aluminum–aluminum Bimetal Fabrication by Squeeze Casting

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

An Investigation into Interface Formation and Mechanical Properties of Aluminum–copper Bimetal by Squeeze Casting

The Effect of the Cu Interlayer on the Interfacial Microstructure and Mechanical Properties of Al/Fe Bimetal by Compound Casting

Bond formation between aluminum-based metal matrix composites and aluminum alloys in compound castings

The pre-hot dipping effects on the bimetal casting of nitriding steel sleeve into the Al-Si matrix

Interfacial Heat Transfer Behavior at Metal/die in Finger-Plated Casting During High Pressure Die Casting Process

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Effect of high entropy alloy as the interlayer on the interfacial microstructure and mechanical property of Al/steel bimetal by compound casting

Effect of Process Parameters, Casting Thickness, and Alloys on the Interfacial Heat-Transfer Coefficient in the High-Pressure Die-Casting Process

Innovative Hybrid High-Pressure Die-Casting Process for Load-Bearing Body-In-White Structural Components

Bonding of Aluminum Alloys in Compound Casting

Determination of the Heat Transfer Coefficient at Metal–die Interface of High Pressure Die Casting Process of AM50 Alloy

Influence of Processing Parameters on Interfacial Heat Transfer Coefficient at the Metal-Die Interface of Die Cast Am50 Alloy

Determination Of The Metal/Die Interfacial Heat Transfer Coefficient And Its Application In Evaluating The Pressure Distribution Inside The Casting During The High Pressure Die Casting Process

Reducing Macroscopic Defects at the Aluminum/Steel Interface in Bimetal Castings Made by the Cummins Process

Liquid-phase diffusion bonding of Al alloy for casting using formate coated insert sheet

Centrifugal Casting Process and Interface Control of Steel/Iron Bimetal Composite

Study on Interfacial Heat Transfer Coefficient at Metal/die Interface During High Pressure Die Casting Process of AZ91D Alloy