Abstract:Cement production is a highly CO 2 -intensive process, where two-thirds of the emissions are unavoidable process emissions and the rest come from the combustion process. Oxyfuel technology is an innovative way to apply carbon capture and allow the industry to reduce CO 2 emissions, even reaching net zero CO 2 emissions. The oxyfuel combustion process can be retrofitted to existing plants and designed for new-build plants, where the plant can be designed with no flue gas recirculation (FGR). A down-scaled kiln burner is tested in oxyfuel conditions with different oxygen-to-fuel ratios in technical and pilot-scale facilities at the University of Stuttgart. In the technical-scale facility, experiments are conducted to compare a case with synthetic FGR at near-stoichiometric conditions (OXY32) and over-stoichiometric conditions (with λ*3.4), λ* being the oxygen-to-fuel ratio. Experiments in the pilot-scale facility are conducted at varying stoichiometric conditions, λ*2, λ*3 and λ*4. In both facilities, a reference case with air combustion is conducted. The highest measured temperature in the air, λ*3 and λ*4 cases were 1020 °C, 1321 °C and 1116 °C, respectively. In the oxyfuel cases, after the peak temperature is reached, the temperature profiles stabilize to similar temperatures as measured in the air case. The inlet oxidizer gas concentration and stoichiometry highly affect the CO and NO formation. For all oxyfuel cases, the CO emission rate in the flue gas measurements is below 20 mg/MJ indicating high burnout efficiency. In the technical-scale tests, the NO emission rate at 2.5 m from the burner is lower in the OXY32 case compared to the air case, with 138 and 247 mg/MJ, respectively. The NO emission rate of the λ*3.4 case is 461 mg/MJ, a consequence of no reducing or reburning zone. The experiments show that the increased over-stoichiometric conditions have a desirable effect on the temperature profile and oxygen can be used as a suitable diluent in comparison to N 2 and CO 2 , but NO formation is increased. In the cement production process, this can be solved by designing a reducing zone in the calciner to properly reduce NO.

Synergistic Integration of Processes Aimed at the Reduction in CO2 Emissions: 1 Use of Oxyfuel Combustion Ash for the Production of Blended Cements

Mitigating CO2 emissions through an industrial symbiosis approach: Leveraging cork ash carbonation

Experimental evaluation of rich oxyfuel combustion characteristics in varying over-stoichiometric conditions

Integration of Chemical Looping Combustion to a Gasified Stream with Low Hydrogen Content

Oxygen Enrichment Technology—An Innovation for Improved Solid Fuel Combustion and Sustainable Environment

Coupled Oxygen-Enriched Combustion in Cement Industry CO2 Capture System: Process Modeling and Exergy Analysis

Catalytic and Non-Catalytic Synergistic Effects and Their Individual Contributions to Improved Combustion Performance of Coal/biomass Blends

Effect of different conditions on the combustion interactions of blended coals in O 2 /CO 2 mixtures

Sustainability assessment for the cement flue gas methanation process using dual functional material (DFM)

Enhancing Simultaneous Desulfurization and Denitrification Efficiency of Cement Kiln Exhaust Gas Via Co-Catalytic Fenton Oxidation Process

Synergistic effect and volatile emission characteristics during co-combustion of biomass and low-rank coal

Influence Of Coal Blending On Ash Fusibility In Reducing Atmosphere

Synergistic consideration of co-treatment of sewage sludge, low-rank coal, and straw for sustainable resource utilization and enhanced energy efficiency: a review

Optimizing co-combustion synergy of soil remediation biomass and pulverized coal toward energetic and gas-to-ash pollution controls

Formulation of low clinker blended cements and concrete with enhanced fresh and hardened properties

Experimental Investigation of Synergistic Behaviors of Lignite and Wasted Activated Sludge During Their Co-Combustion

Accelerated Direct Carbonation of Steel Slag and Cement Kiln Dust: An Industrial Symbiosis Strategy Applied in the Bergamo-Brescia Area

Combustion behavior of co-injecting flux, pulverized coal, and natural gas in blast furnace and its influence on blast furnace smelting

Oxy-fuel co-combustion characteristics and kinetics of various ultra-low volatile coal-based solid waste blends

Environmental impact assessment of post-combustion CO2 capture technologies applied to cement production plants

Auto-Combustion of Corn Straw: Production and Characterization of Corn Straw Ash (CSA) for Its Use in Portland Cement Mortars