Abstract:The rapid economic development and increasing consumption of electrical energy requires people to generate more energy. The new energy sources developed are required to be clean and environmentally friendly. Microfluidic energy harvesting device is relatively less known compared with other popular renewable energy sources, such as solar cell and bio-fuels, but can provide such a clean and environmentally-friendly source. The classical electrokinetic energy conversion mechanism relies on a single stage conversion by forcing liquid through a channel with charged walls. When the net charges inside the electrical double layer (EDL) are transported by water flow, the produced electrical energy can be harvested via connection of electrodes at two ends of a channel. Different from traditional single phase flow energy conversion, the liquid microjet was used for energy conversion. Applied pressure forces water flow through a micropore, forming a liquid jet. Then the jet broke into droplets, which are absolutely isolated by air. Droplet kinetic energy is converted to electrical energy when the charged droplets decelerate in the electrical field that forms between membrane and target. It operates entirely different with traditional energy conversion from streaming potential, hence we term it “ballistic energy conversion”. Conversion occurs in two stages: first pressure is converted to kinetic energy and subsequently kinetic energy is converted to electrical energy. In the first stage a stream of high-velocity high-charge droplets is produced by forcing water through a micropore. In the second stage the charged droplets travel through an electrical field towards a high-potential target, decelerating them to zero speed. The target acquires its potential by droplet impact. Current is drawn from the target to do useful work. We strongly reduced loss factors by optimizing the setup from the physical model. At present this resulted in an energy conversion efficiency of almost 50% with as main loss factor hydrodynamic friction losses in the micropore. Now, inspired by Kelvin’s water dropper, we apply the electrostatic charge self-induction mechanism to an inertia-driven (ballistic) energy conversion system, and show the disadvantages of Kelvin’s water dropper do not any more apply. The droplet charge thereby is derived from the same inductive charging mechanism as in Kelvin’s droplet generator, employing two separate systems and cross-connecting targets and induction rings. To prevent overcharging of the droplets by the inductive mechanism and consequent droplet loss by repulsion from the target, we use voltage dividers, trying both a resistor divider and a diode divider, to enable stable energy conversion with a self-induction system. The current rapidly increased once the electrical circuit was connected. With reversely connected diodes, the induction voltage could be properly controlled to a saturated value (about 500V), whereby experimentally maximal 17.9% energy conversion efficiency was obtained with the diode-induced system.

Optimizing liquid water jet on energy conversion performance

High Efficiency Energy Conversion from Liquid Jet Flow

Droplet-enabled controllable manipulation of tribo-charges from liquid-solid interface

Ballistic Energy Conversion: Physical Modeling and Optical Characterization

Energy Harvesting from Water Streaming at Charged Surface.

The microfluidic energy conversion by droplets

High-efficiency ballistic electrostatic generator using microdroplets

Liquid-Solid Slip on Charged Walls: the Dramatic Impact of Charge Distribution.

Energy Conversion During Electrically Actuated Jumping of Droplets

Dynamical Mechanism for Reaching Ultrahigh Voltages from a Falling Droplet

Ballistic Energy Conversion with 78% Efficiency and System Integration

Strong enhancement of streaming current power by application of two phase flow.

Vertical impact of a water jet on a hot plate: From a growing drop to spray formation

Surface Wave and Splashing of Liquid Film by Oblique Water Jet Impinging on a Vertical Plate

Combined effect of Fluid Rheology and Surface Modification on Eletrokinetic Energy Generation through Finite Length Microchannel

Breaking the symmetry to suppress the Plateau–Rayleigh instability and optimize hydropower utilization

Conversion of surface energy and experimental investigation on the self-motion behaviors of liquid droplets on gradient surfaces

A Droplet Energy Harvesting And Actuation System For Self-Powered Digital Microfluidics

Hydrodynamic Constraints on the Energy Efficiency of Droplet Electricity Generators

Performance Simulation on a New Type of Liquid Pump

Numerical study on the atomization mechanism and energy characteristics of synthetic jet/dual synthetic jets