Abstract:Sandwich piezoelectric transducers are widely used in many industrial applications due to their attractive advantages of compact structure, no electromagnetic interference, and excellent output performance. V-shaped piezoelectric transducers, a typical design, have been adopted as the stator of ultrasonic motors and the machining tool of elliptical vibration surface manufacturing. However, traditional V-shaped piezoelectric transducers were designed with one contact interface to output effective vibration, limiting their applications. To achieve multi contact areas with synchronous actuation function, a novel three-dimensional sandwich piezoelectric transducer is proposed in this study, expecting to drive wheels of a robotic mobile system. Two orthogonal Langevin transducers are adopted to vertically couple in a cylinder, producing two bending vibrations with a spatial phase difference of pi/2 in the cylinder. Therefore, elliptical motion is generated at surface points of two driving parts placed at both ends of the cylinder. Due to the fact that two front-end blocks of the two Langevin transducers and the cylinder form a three-dimensional configuration which hard to be manufactured by traditional machining methods, this part is printed using laser additive manufacturing. To analyze the dynamic behavior of the proposed three-dimensional transducer, an analytical model is carried out utilizing the transfer matrix method for providing systematic modeling. This developed transfer matrix model is not only capable of greatly reducing computation efforts, and it is maybe suitable for the analysis of traditional V-shaped transducers. To validate this developed transfer matrix model and confirm the feasibility of the transducer design, experimental investigations are conducted to measure the vibration characteristics of the proposed transducer prototype using a 3D laser Doppler vibrometer and are compared to the calculation results. The measured and computed resonant frequencies of the transducer are 19.975 kHz and 20.045 kHz for the symmetrical vibration mode, and 20.07 kHz and 20.06 kHz for the anti-symmetrical vibration mode, respectively. Comparisons show that calculation results match well with the experimental results, demonstrating the effectiveness of the developed transfer matrix model and the feasibility of the three-dimensional transducer design. (C) 2018 Elsevier Ltd. All rights reserved.

Large-dimension Piezoelectric Ceramic Composite Transducer with Point-Defect, Square-Lattice Phononic Crystal

Defect Mode-Induced Unidirectional Flexural Wave Transmission Using Prismatic Beams with Concentrated Gradient Masses

On‐Chip Tightly Confined Guiding and Splitting of Surface Acoustic Waves Using Line Defects in Phononic Crystals

Topological Imbalanced Phononic Crystal with Semi-Enclosed Defect for High-Performance Acoustic Energy Confinement and Harvesting

A Novel Additive Manufactured Three-Dimensional Piezoelectric Transducer: Systematic Modeling and Experimental Validation

L-shape triple defects in a phononic crystal for broadband piezoelectric energy harvesting

Investigation of Deep-Sea Longitudinal Vibration Cavity Resonant Coupling Transducers Made of Relaxor Ferroelectric Single-Crystal Material

Elastic Wave Harvesting in Piezoelectric-Defect-introduced Phononic Crystal Microplates

Research on Wave Bandgaps Inacircular Plate of Radial Phononic Crystal

Phononic crystals with incomplete line defects: Applications in high-performance and broadband acoustic energy localization and harvesting

Band Gap And Defect State Engineering In A Multi-Stub Phononic Crystal Plate

Design and fabrication of non-periodic 1–3 composite structure for ultrasonic transducer application

Enhanced Energy Localization and Harvesting by Design of Phononic Crystal Defects

Conformally Large-Area Single-Crystal Piezocomposites with High Performance for Acoustic Transducers

The investigation of point defect modes of phononic crystal for high Q resonance

Research on Intelligent Optimization Design of Large-scale Three-dimensional Ultrasonic Vibration System

High-Frequency Vibration Analysis of Piezoelectric Array Sensor under Lateral-Field-Excitation Based on Crystals with 3 M Point Group.

Design of Piezoelectric Ultrasonic Transducer Based on Doped PDMS

Design and Fabrication of 1-3 Piezoelectric Composite Material Air Coupled Ultrasonic Transducer

Design of phononic crystals using superposition of defect and gradient-index for enhanced wave focusing

Integrated high-frequency piezoelectric transducer within radial critical dimension of piezoceramics