Abstract:Abstract Internal cooling structures for gas turbine engines are becoming more complicated to push the hot gas temperature as high as possible, which, however, allows particulates drawn into the coolant air to be more readily to deposit within these passages and thus greatly affect their flow loss and thermal performance. In this study, internal swirl cooling and jet impingement cooling subjected to particulate deposition were evaluated and compared using a conjugate heat transfer method, with an emphasis on the thermal effects of the insulative deposits. To accomplish the goal, an unsteady conjugate mesh morphing simulation framework was developed and validated, which involved particle tracking in an unsteady fluid flow, particle–wall interaction modeling, conjugate mesh morphing of both fluid and solid domains, and a deposit identification method. The swirl and the jet impingement cooling configurations modeled the internal cooling passage for the leading-edge region of a turbine blade and were investigated in a dust-laden coolant environment at real engine conditions. Coupling effects between the dynamic deposition process and the unsteady flow inside the two cooling channels were examined and the insulative effects of the deposits were quantified by comparing the temperatures on the external and internal surfaces of the metal channel walls, as well as on the deposit layers. Results demonstrated the ability of the newly developed, unsteady conjugate simulation framework to identify the deposits from the original bare wall surface and to predict the insulation effects of the deposits in the dynamic deposition process. The dust almost covered the entire impingement channel, while deposits were only seen in the vicinity of the jets in the swirl channel. Despite this, a dramatical decrease of convection heat transfer was found in the swirl channel because the swirling flow was sensitive to the interruption of the deposits. In contrast, the deposits improved the heat transfer rate in the impingement channel. When the thermal effects of the deposit layer were taken into account, the wall temperatures of both two cooling geometries were substantially elevated, exceeding the allowable temperature of the metal material. Due to the denser deposit coverage, the impingement channel wall had a greater temperature increase than the swirl channel. In terms of flow loss, the presence of the deposits inhibited the swirl intensity by interrupting the swirling flow and thus reduced the friction loss, whereas the pressure loss was improved by the deposits in the impingement cooling.

Effects of Coolant Temperature on Particulate Deposition and Cooling Efficiency of EGR Coolers

Effects of Gas Flow on Particulate Deposition in EGR Coolers

Effect of Hydrocarbon Concentration on Particulate Deposition and Microstructure of the Deposit in Exhaust Gas Recirculation Cooler

Effect of Hydrocarbon Condensation on Fouling and Heat Exchange Efficiency in EGR Cooler

An Original Nondestructive Sampling Method to Study the Effect of Gravity on the Deposition of Micron-Sized Large Particles in Exhaust Gas Recirculation (EGR) Cooler Fouling

Three condensation paths of exhaust and its five effects on exhaust gas recirculation (EGR) cooler fouling and thermal performance: A review

Numerical Analysis Of Cooling Tower Water Fouling In Enhanced Tubes

Experimental assessment of film cooling from cylindrical holes subject to particulate deposition

Evolution of EGR cooler deposits under hydrocarbon condensation: Analysis of local thickness, roughness, and fouling layer density

A Study of Practical Cooling Water-and Particulate Fouling Characteristics in Spiral-grooved Tubes

Analysis of Cooling Tower Fouling in Enhanced Tubes Based on the Prandtl Analogy

Effects of the Changes of Load and Flue Gas Temperature on the Emission of Particulate Matter from the Coal-Fired Unit

Particulate Fouling and Composite Fouling Assessment in Corrugated Plate Heat Exchangers

Analysis of Fouling Characteristic in Enhanced Tubes Using Multiple Heat and Mass Transfer Analogies

Fouling in enhanced tubes using cooling tower water: Part II: combined particulate and precipitation fouling

Hybrid high-temperature fouling and erosion characteristics of gas-particle flow around heating tube via CFD-DEM

Conjugate Heat Transfer Evaluation of Turbine Blade Leading-Edge Swirl and Jet Impingement Cooling With Particulate Deposition

Effects of Temperature and Particle Size on Deposition in Land Based Turbines

Experimental study on the fouling and heat transfer characteristics of enhanced tubes used in a cooling tower water system with the actual water quality

Experimental And Numerical Investigation Of Transpiration Cooling For Sintered Porous Flat Plates

Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh