Abstract:The investigation of frictional pressure drops in wire-wrapped bundles at low flow velocities is crucial for thermal-hydraulic studies of sodium-cooled fast reactor cores. This study aims to refine empirical formulas for predicting friction factors in wire-wrapped bundles by addressing their limitations in accurately calculating friction factors during transition regime. By analyzing existing empirical formulas and meticulously observing frictional pressure drop experiments conducted under low-flow conditions that reported in the literature, the study proposes and demonstrates the mechanism of the laminar-to-transitional regime transition in wire-wrapped bundles. Additionally, experimental research was conducted on the frictional pressure drop of a 37-rod wire-wrapped bundle. A novel high-precision differential pressure measurement technique, the photographic liquid column manometer, was employed to enhance frictional pressure drop measurement accuracy. This innovative method achieves a measurement uncertainty of less than 2 Pa within a range of 0 to 300 Pa. The mass flow rate of the fluid was measured and converted to obtain the flow velocity through the assembly, further improving the accuracy of flow velocity measurements. The analysis and experiments reveal that the transition from the laminar to transitional regime does not occur uniformly but initiates locally in certain subchannels before spreading across the assembly as flow velocity increases. Significant increases in the frictional pressure drop occur only after a sufficient number of subchannels have undergone transition. This perspective is supported by extensive existing literature, which report that in assemblies with fewer rod bundles, smaller P/D and H/D values, and constructed from hard metal materials such as stainless steel, the friction factor at the initial stage of the transitional regime shows a significant increase or remains constant with increasing Reynolds number. Under these conditions, the high consistency of the P/D ratio within the assembly causes the fluid to transition within a narrow range of flow velocities, leading to a marked increase in the friction factor with Reynolds number. The research results also indicate that the prediction accuracy of the critical Reynolds number for the laminar-to-transitional flow transition significantly impacts the calculation accuracy of empirical formulas at low flow velocities. Formulas using smaller predicted values of the critical Reynolds number show better agreement between predicted values and the measured results in this study. Therefore, the study recommends adopting smaller critical Reynolds numbers and interpolation indices in empirical formulas to facilitate an early onset and smooth transition of laminar-to-transitional regime behavior in friction factors, thereby improving the accuracy of calculated friction factors.

Experimental Investigation of the Friction Factor of Wire-Wrapped Bundles at Low Velocities under Natural Circulation Flow Conditions

Experimental Study on Frictional Pressure Drop Characteristics of Wire-wrapped Bundles in Transition Flow

An Experiment Study of Pressure Drop and Flow Distribution in Subchannels of a 37-Pin Wire-Wrapped Rod Bundle

Investigation on Entropy Generation and Flow Characteristics of 7-Pin Sodium Cooled Wrapped-Wire Fuel Bundle

Frictional Resistance Investigation of Sco2 and a Semi-Empirical Friction Factor Correlation Based on Wall-of-the-law

Experimental Study of Liquid Sodium Flow and Heat Transfer Characteristics along a Hexagonal 7-Rod Bundle

Thermal-hydraulic Analysis of a 7-Pin Sodium-Cooled Fast Reactor Wire-Wrapped Fuel Bundle

Pressure Drop in Seven-Pin Wire-Wrapped Rod Bundle for the Sodium Cartridge Loop in Versatile Test Reactor

Periodicity and transversal pressure distribution in a Wire‐wrapped 19‐Pin fuel assembly

Experimental Investigation of the Subchannel Axial Pressure Drop and Hydraulic Characteristics of a 61-Pin Wire Wrapped Rod Bundle

Experimental investigation of the crossflow of water in a 7-pin wire-wrapped rod bundle

CFD Investigation on Thermal-Hydraulic Behaviors of a Wire-Wrapped Fuel Subassembly for Sodium-Cooled Fast Reactor

Flow analysis in a 37-pin wire-wrapped rod bundle for sodium-cooled fast reactor using magnetic resonance velocimetry. I. Validation and gross behavior

Numerical Investigation of Special Heat Transfer Phenomenon in Wire-Wrapped Fuel Rod of SFR

Numerical Investigation for the Heat Transfer Mechanisms Between Subchannels of Bar Rod Bundles Cooled by Liquid Sodium

A Porous Medium Model for Simulating Conjugate Heat Transfer Between Wire-Wrapped Fuel Bundles under Forced and Mixed Convection

Flow analysis in a 37-pin wire-wrapped rod bundle for sodium-cooled fast reactor using magnetic resonance velocimetry. II. Detailed characterization and influence of wire angular position

CFD Simulation of a 61-pin Wire-wrapped Fuel Subassembly for Sodium Cooled Fast Reactor

Experimental and Numerical Investigation on Flow Characteristics of Inter-Wrapper Channel in LMFBR

Numerical Study on the Thermal Hydraulic Characteristics in a Wire-Wrapped Assembly of LFRs

NUMERICAL SIMULATION OF THERMO-HYDRAULIC CHARACTERISTICS OF 7-PIN SFR TEST FUEL BUNDLE WITH VARIABLE-PITCH HELICAL WIRE