Abstract:This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

Geometrical Nonlinear Analysis Of Thin Composite Plates Based On Dkt Element

Static and free vibration analysis of laminated composite plates using isogeometric approach based on the third order shear deformation theory

Non-Linear Analysis of Laminated Composite Plates under General Out-Of-Plane Loading

Geometrically Nonlinear Analysis of Laminated Compos ite Plates subjected to Uniform D istributed Load Using a New Hy- pothesis: the finite element method (FEM) Approach

Isogeometric nonlinear bending and buckling analysis of variable-thickness composite plate structures

Nonlinear Dynamic Analysis for Rectangular FGM Plates with Variable Thickness Subjected to Mechanical Load

Analysis of the Dynamic Behavior, Buckling, and Aeroelasticity of a thin Composite Plate with the Effect of General and Local Geometric Defects

A new nonlinear finite element model for transient dynamic response of a micro composite plate embedded with micro SMA wires considering the size effects

Nonlinear Analysis Of Thick Plates By Ht Fe Approach

The new flat shell element DKMGQ-CR in linear and geometric nonlinear analysis

Analysis of the dynamic response for Kirchhoff plates by the element-free Galerkin method

Geometrically nonlinear free vibration analysis of laminated composite plates: A finite element assessment of a higher order non-polynomial shear deformation theory

Nonlinear free vibration analysis of laminated composite plates and shell panels using non-polynomial higher-order shear deformation theory

Generalized Conforming Element For The Analysis Of The Laminated Composite Plates

Non-Linear Analysis of Functionally Graded Fiber Reinforced Composite Laminated Plates, Part I: Theory and Solutions

Isogeometric finite element analysis of laminated composite plates based on a four variable refined plate theory

Geometrically nonlinear isogeometric analysis of laminated composite plates based on higher-order shear deformation theory

A New Triangular Displacement-Based Element for the Analysis of Laminated Composite Plates and Improvement Stress Solutions by a Hybrid Procedure

A New Composite Plate/plate Element for Stiffened Plate Structures Via Absolute Nodal Coordinate Formulation

Non-linear deflection and stress analysis of laminated composite sandwich plate with elliptical cutout under different transverse loadings in hygro-thermal environment

Kirchhoff-Love Plate Theory: First-Order Analysis, Second-Order Analysis, Plate Buckling Analysis, and Vibration Analysis Using the Finite Difference Method