Abstract:Four different thin film nanocomposite (TFN) membranes were prepared by adding different concentrations of porous Zr-MOFs (UiO-66 and UiO-66-NH2) to piperazine (PIP) aqueous solution (aqueous phase) or 1,3,5-Benzenetricarbonyl trichloride (TMC)-n-hexane solution (organic phase) by interfacial polymerization. The main purpose is to study the specific effects of different addition methods and addition amounts of nanoparticles on the structure and performance of the TFN membranes by interfacial polymerization. All four TFN membranes exhibited higher water permeability while maintaining high salt rejection compared to thin film composite (TFC) membrane. On the one hand, the TFN membranes behaves differently which are prepared by adding the same kind of nanoparticles to the aqueous phase or organic phase, respectively. The TFN membrane prepared by adding 0.2 w/v% UiO-66 to the organic phase had high water flux of 87.86 L·m-2·h-1, comparing 46.31 L·m-2·h-1 of membrane prepared by adding 0.3 w/v% UiO-66 in the aqueous phase. This is due to the fact that UiO-66 greatly slows the interfacial polymerization rate when UiO-66 is added to the organic phase, resulting in a thinner and more aperture polyamide thin film layer, reducing the water transmission resistance during filtration. Therefore, it is more economical by adding nanoparticles to organic phase than aqueous phase under the same filtering effect. On the other hand, different nanoparticles can also cause differences in performance and structure of the TFN membranes even in the same preparation manner. TFN membrane with UiO-66-NH2 in the aqueous phase has higher water permeance than the one with UiO-66 in the aqueous phase, owning to good hydrophilicity of amino group, which improves the water dispersibility of UiO-66-NH2, so that the TFN membrane is more uniform. In addition, UiO-66-NH2 slows down the process of interface polymerization, making the membrane more porous. The monomers in aqueous phase and the organic phase can be adsorbed in the pores of Zr-MOFs, which makes the interfacial polymerization occur both in the pores and on the surface of the pores. Thus, the compatibility between the polyamide and MOFs was enhanced and less defects was formed in the thin film layer, resulting in high salt rejection even the concentration of Zr-MOFs increased. This is the first time to explain that polyamide membrane has not obvious salt rejection attenuation with increasing porous material content using pore adsorption reaction monomer principle. Also, the Zr-MOFs based TFN membrane exhibited good heat resistance and anti-fouling property. This work shows that porous Zr-MOFs nanomaterials have significant advantages in the development of nanofiltration membranes with high water flux and rejection.

Advantages of polydopamine coating in the design of ZIF-8-filled thin-film nanocomposite (TFN) membranes for desalination

Hydrophilic Modified Polydopamine Tailored Heterogeneous Polyamide in Thin-Film Nanocomposite Membranes for Enhanced Separation Performance and Anti-Fouling Properties

Impact of Graphitic Carbon Nitride/polydopamine on Permeance and Antifouling Performance of Reverse Osmosis Membranes

Preparation and characterization of surface-modified zeolite-polyamide thin film nanocomposite membranes for desalination

Amphiphilic Interlayer Regulated Interfacial Polymerization for Constructing Polyamide Nanofiltration Membranes with High Perm-Selectivity of Mono-/Divalent Salts

In-situ Interfacial Polymerization of Polyamide TFN Membranes by Adding a Diamino-Silane Coupling Agent: Toward Enhanced Desalination Performance

ZIF-8-incorporated thin-film nanocomposite (TFN) nanofiltration membranes: Importance of particle deposition methods on structure and performance

Improvement of the Zeolite-Polyamide Nanocomposite Reverse Osmosis Membrane for Desalination

Enhancing interface compatibility of UiO-66-NH2 and polyamide by incorporating dopamine into thin film nanocomposite membranes

Preparation of zeolite/polyamide nanocomposite reverse osmosis membrane

Improved separation performance of polyamide based reverse osmosis membrane incorporated with poly(dopamine) coated carbon nanotubes

Incorporation of dendritic silica nanoparticles for the preparation of high‐performance thin‐film nanocomposite membranes

High-performance Nanofiltration Membranes with a Polyamide-Polyester Composite Layer and a Polydopamine Surface Layer for Desalination and Dye Pollutant Removal

Hydrophilic yolk-shell ZIF-8 modified polyamide thin-film nanocomposite membrane with improved permeability and selectivity

Facile preparation of nanochannel membrane based on polydopamine modified porous organic polymer nanoparticles for high-efficient dye desalination

MOF-808/Polyamide Thin-Film Nanocomposite Membranes for Efficient Nanofiltration

Incorporating ionic carbon dots in polyamide nanofiltration membranes for high perm-selectivity and antifouling performance

Porous Zr-based metal organic frameworks (Zr-MOFs) incorporated thin film nanocomposite membrane toward enhanced desalination performance.

Thin Film Nanocomposite Membranes Based on Zeolitic Imidazolate Framework-8/Halloysite Nanotube Composites

MoS2 @PDA thin-film nanocomposite nanofiltration membrane for simultaneously improved permeability and selectivity

Polydopamine Coating on a Thin Film Composite Forward Osmosis Membrane for Enhanced Mass Transport and Antifouling Performance