Abstract:Titanium alloys (Ti-6Al-4V) are promising materials as bone implants in clinical surgeries owing to their excellent performances. However, wear debris caused by the tribological behavior of the cortical bone and titanium alloy interface were found to be paramount for implant stability. The contact environment between the cortical bone and Ti-6Al-4V in vivo has been considered to affect the tribological behavior. Currently, the tribological behaviors of bone and Ti-6Al-4V in different biolubricants remain elusive. Therefore, in this work, the tribological behaviors of Ti-6Al-4V plates sliding against bovine cortical bone were investigated in dry sliding and in biolubricants of physiological saline (PS), simulated body fluids (SBF), and fetal bovine serum (FBS). Results show that the friction coefficient and wear rate of the bovine cortical bone and Ti-6Al-4V interface exhibit the same sequence as follows: FBS > SBF > PS > dry sliding. These results are attributed to bone hardness variation and corrosion of different biolubricants. Meanwhile, the effects of normal load and velocity on the tribological behavior of bone and Ti-6Al-4V interface were also investigated in dry sliding and three different biolubricants. Results show that as the normal load is increased and the sliding velocity is decreased, the friction coefficient decreases in dry condition, adhering to the Hertz contact theory. However, according to the boundary lubrication theory, the friction coefficient in three biolubricants correlates positively to the normal load and negatively to the sliding velocity. Moreover, the wear rates of the bone samples increase with the increase in normal load and sliding velocity under dry and biolubrication conditions. Finally, the characterization results indicate that the wear mechanisms of the cortical bone and Ti-6Al-4V interface in dry friction are primarily adhesive and abrasive wear. Further, corrosive wear occurs in biolubrications, apart from adhesive and abrasive wear.

Study on the Effect of Hydrodynamic Pressure on the Tribological Performance of Textured Bioimplants

Advances in artificial joint bio-friction and wear simulation assessment technology

An experimental analysis of the hydrodynamic contribution of textured thrust bearings during steady-state operation: A comparison with the untextured parallel surface configuration

Experimental Study of Tribological Performance on Silicon Micro-textured Surface

Evaluation of tribological performance for laser textured surfaces with diverse wettabilities under water/oil lubrication environments

A Pocket-Textured Surface for Improving the Tribological Properties of Point Contact under Starved Lubrication

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Effect of Micro-Dimple Geometry on the Tribological Characteristics of Textured Surfaces

The Effect of Laser Texturing of Steel Surfaces on Film Lubriction Based on Stribeck Curves

Effect of surface texture on the frictional properties of grease lubricated spherical plain bearings under reciprocating swing conditions

Coupled effect of filler and countersurface roughness on the tribological performance of the PEEK-PTFE-steel hybrid wear system

Research Progress on the Design of Surface Texture in Tribological Applications: A Mini-Review

Tribological Behavior of Ti-6Al-4V Against Cortical Bone in Different Biolubricants.

An Experimental Investigation of Tribological Performance of Triangular Textures in Water Lubrication Regime

A study on tribological properties of textured Co-Cr-Mo alloy for artificial hip joints

Research in Improving Tribology Performance by Surface Texturing

Effects of different surface textures on tribological performances of the cylinder liner-piston ring: An experimental study

Anti-friction mechanism of sinusoidal texture with various intervals: the synergistic effect of dynamic pressure and tribofilm

Simulation and Experimental Study on Tribological Properties of Herringbone Texture on 42CrMo Bearing Alloy Steel Surface

Optimization of Bionic Texture Parameters by Box–Behnken Method and Study on Tribological Performance of 42CrMo Self-Lubricating Composites in Solid–Liquid Composite Lubrication System

Performance evaluation of different types of micro-textured hydrostatic spindles under the main influencing factors