Abstract:The microstructural evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration in the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration in cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1 °C/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0 °C/s, the proportion of large-angle grain boundaries was only 27.1%, and the dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of the FeO phase in the scale phase gradually decreased, and the proportion of the Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and area reduction first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

Effect of Sub-rapid Solidification and Secondary Cooling on Microstructure and Properties of Strip Cast Low-Carbon Bainitic–Martensitic Steel

Microstructure Evolution and Mechanical Property of Cu-Bearing High-Strength Steel Produced by Simulated Strip Casting

Evolution of primary carbides during accelerated solidification process of high-carbon martensitic stainless steels

Effect of cooling rate on microstructure and mechanical properties of a low-carbon low-alloy steel

The Effect of Relaxing on the Grain Refinement of Low Carbon High Strength Microalloyed Steel Produced by Compact Strip Production

Simulation of Subrapid Solidification and Secondary Cooling for the Strip Casting of IF Steel

Microstructure Analysis and Quantitative Strengthening Evaluation of Medium Carbon Bainitic Multiphase Steel

Kinetics of austenite growth and bainite transformation during reheating and cooling treatments of high strength microalloyed steel produced by sub-rapid solidification

Low-Carbon Bainite Steel with High Strength and Toughness Processed by Recrystallization Controlled Rolling and Ultra Fast Cooling (RCR+UFC)

Dynamic continuous cooling transformation, microstructure and mechanical properties of medium-carbon carbide-free bainitic steel

Influence of cooling rate on microstructure evolution in a low carbon high strength microalloyed dual phase steel

Microstructure Formation in Rapidly Solidified AISI 304 Stainless Steel Strip

Effect of Cooling Rate on Microstructure and Mechanical Properties of a Microlaminated Low-Density Steel

The Properties of 1500 Mpa Grade Alloy Steel with Carbide Free Bainite/Martensite Mixed Microstructures

Effect of Carbon Distribution Range in Mixed Bainite/martensite/retained Austenite Microstructure on Mechanical Properties

Effect of Initial Microstructure on Microstructure and Properties of Bainitic Steels Achieved by Rapid Heat Treatment

Microstructure and mechanical behavior of a low-density Fe–12Mn–9Al–1.2C steel prepared using centrifugal casting under near-rapid solidification

Effect of Cooling Rate on Microstructure Evolution and Mechanical Properties of SCM435 Steel

Microstructure and mechanical properties of Nb-B bearing low carbon steel plate: Ultrafast cooling versus accelerated cooling

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes