Abstract:A new thermomechanical process consisting of heavy cold rolling (HCR) and short-time heat treatment (STH) is developed to fabricate fine-grained martensite microstructure in a low-cost plain low-carbon steel. To achieve the optimal mechanical properties after STH, three different ferrite-pearlite (F-P) dual-phase microstructures are prepared via hot rolling (HR), HR and austenitizing, and HR and HCR. The microstructure evolution and the comprehensive mechanical properties of the alloy during STH are then investigated. We find that the volume fractions of transformed martensite after STH increase with decreasing grain sizes of the pre-STH F-P dual phases. The rapid heating and short-time holding of STH promote grain nucleation and inhibit grain growth, resulting in microstructure refinement. The formation of martensites with different morphologies and different carbon concentrations in the HR and HCR + STH alloy is identified, owing to the inhomogeneous carbon distribution by STH. Tensile experiments demonstrate that STH greatly improves the comprehension mechanical properties of the alloy. Excellent mechanical properties, with a yield strength of 1224 MPa, a tensile strength of 1583 MPa, a uniform elongation of 4.0% and a total elongation of 7.3% are achieved in the HR and HCR + STH alloy. These excellent mechanical properties are principally attributed to the microstructure refinement and martensite formation induced by STH, with a yield strength improvement of 134% and a tensile strength improvement of 150% relative to the HR alloy.

Comparison on Tensile Characteristics of Plain C–Mn Steel with Ultrafine Grained Ferrite/Cementite Microstructure and Coarse Grained Ferrite/Pearlite Microstructure

Mechanical Properties of Plain Carbon Steels with Ultrafine (α+θ) Microstructures

Relationship between microstructure and yield strength for plain carbon steel with ultrafine or fine (ferrite+cementite) structure

Enhancement of mechanical properties by changing microstructure in the eutectoid steel

Microstructure Evolution and Mechanical Properties of Eutectoid Steel with Ultrafine or Fine (ferrite+cementite) Structure

High Tensile Ductility and High Strength in Ultrafine-Grained Low-Carbon Steel

Microstructural Evolution and Mechanical Property of Ultrafine-Grained Pearlitic Steel by Cold Rolling: the Influence of Cementite Morphology

The Properties of 1500 Mpa Grade Alloy Steel with Carbide Free Bainite/Martensite Mixed Microstructures

Dependence of Tensile Properties on Microstructural Features of Bimodal-Sized Ferrite/cementite Steels

Microstructures and Tensile Properties of 9Cr-F/M Steel at Elevated Temperatures

Microstructures and Mechanical Properties of Ferrite-Based Lightweight Steel with Different Compositions

Microstructure Evolution and Work Hardening Behavior of Medium/high Carbon Fe-Mn-C TWIP Steel During Tensile Deformation at 298 K and 223 K

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

INFLUENCE OF C AND Mn CONTENT OF LOW CARBON STEEL ON ULTRA-FINE FERRITE MICROSTRUCTURE FORMATION DURING ANNEALING AFTER DEFORMATION-ENHANCED TRANSFORMATION

Microstructure and mechanical properties of a 1.6C (pct) ultra-fine grained ultra-high carbon steel

Microstructure Evolution and Mechanical Properties of Ferrite–Austenite Duplex Fe-Mn-Al-(Cu)-C Steel under Different Annealing Temperatures

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Excellent Ultra-Cryogenic Tensile Properties of Al-containing Fe-Mn-C High Manganese Austenitic Steel

A Comparative Study on the Dynamic Tensile Behavior of Nanostructured Bainitic and Quenched-Tempered Martensitic Steels

Microstructure and Properties of 1.6%C Ultra-high Carbon Steel

Stabilized Uniform Deformation in A High-Strength Ferrite-Cementite Steel with Multiscale Lamellar Structure