Abstract:A basic attribute for turbine blade film cooling is that coolant injected should be largely passively convected by the local base flow. However the effective working of the conventional wisdom may be compromised when the cooling injection strongly interacts with the base flow. Rotor blade tip of a transonic high-pressure (HP) turbine is one of such challenging regions for which basic understanding of the relevant aerothermal behavior as a basis for effective heat transfer/cooling design is lacking. The need to increase our understanding and predictability for high speed transonic blade tip has been underlined by some recent findings that tip heat transfer characteristics in a transonic flow are qualitatively different from those at a low speed. Although there have been extensive studies previously on squealer blade tip cooling, there have been no published experimental studies under a transonic flow condition.The present study investigates the effect of cooling injection on a transonic squealer tip through a closely combined experimental and CFD effort. The experimental and computational results as presented in Part 1 have consistently revealed some distinctive aerothermal signatures of the strong coolant-base flow interactions. In this paper as Part 2, detailed analyses using the validated CFD solutions are conducted to identify, analyze and understand the causal links between the aerothermal signatures and the driving flow structures and physical mechanisms.It is shown that the interactions between the coolant injection and the base Over-Tip Leakage (OTL) flow in the squealer tip region are much stronger in the frontal subsonic region than the rear transonic region. The dominant vortical flow structure is a counter-rotating vortex pair (CRVP) associated with each discrete cooling injection. High HTC stripes on the cavity floor are directly linked to the impingement heat transfer augmentation associated with one leg of the CRVP, which is considerably enhanced by the near floor fluid movement driven by the overall pressure gradient along the camber line. The strength of the coolant-base flow interaction as signified by the augmented values of the HTC stripes is seen to correlate to the interplay and balance between the OTL flow and the CRVP structure. As such, for the frontal subsonic part of the cavity, there is a prevailing spanwise inward flow initiated by the CRVP, which has profoundly changed the local base flow, leading to high HTC stripes on the cavity floor. On the other hand, for the rear high speed part, the high inertia of the OTL flow dominates, thus the vortical flow disturbances associated with the CRVP are largely passively convected, leaving clear signatures on the top surface of the suction surface rim. A further interesting side-effect of the strong interaction in the frontal subsonic region is that there is considerable net heat flux reduction in an area seemingly unreachable by the injected coolant. The present results have confirmed that this is due to the large reduction in the local HTC as a consequence of the upstream propagated impact of the strong coolant-base flow interactions.

Rotating Effect On Transonic Squealer Tip Cooling Performance

Interaction Mechanism of Transonic Squealer Tip Cooling with the Effect of High-Speed Relative Casing Motion

Cooling Injection Effect on A Transonic Squealer Tip - Part 1: Experimental Heat Transfer Results and Cfd Validation

Research on Turbine Blade Squealer Tip Film Holes Arrangement and Moving Shroud

Cooling Injection Effect on A Transonic Squealer Tip - Part 2: Analysis of Aerothermal Interaction Physics

RELATIVE CASING MOTION EFFECT ON SQUEALER TIP COOLING PERFORMANCE AT TIGHT TIP CLEARANCE

An Experimental Investigation of Adiabatic Film Cooling Effectiveness and Heat Transfer Coefficient on a Transonic Squealer Tip

Investigation Of Film Cooling Effectiveness On Squealer Tip Of A Gas Turbine Blade

Aerothermal Characteristics of Transonic Over-Tip Leakage Flow for Different Tip Geometries with Cooling Injection

Investigations of Unsteady Film Cooling Performance on Rotor Squealer Tip

Numerical Investigations on the Heat Transfer Performance of Transonic Squealer Tip With Different Film Cooling Layouts

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

NUMERICAL STUDY OF BLADE TIP COOLING AT HIGH SPEED WITH TIP AND PRESSURE-SIDE COOLANT INJECTIONS

Investigation of Leakage Flow and Heat Transfer in A Gas Turbine Blade Tip with Emphasis on the Effect of Rotation

Investigations of Heat Transfer and Film Cooling Effect on a Worn Squealer Tip

Aerothermal characteristics evaluation for different tip configurations without and with film cooling on transonic turbine

Effects of Rotor Squealer Tip with Non-Uniform Heights on Heat Transfer Characteristic and Flow Structure of Turbine Stage

Effect of squealer rim slot structure on turbine blade aerothermal performance

Influence of Incidence Angle and Squealer Tip Cutback on the Aerothermal Performance of a Transonic Turbine Blade

Influence of Gas-to-Wall Temperature Ratio on the Leakage Flow and Cooling Performance of a Turbine Squealer Tip

An Investigation on Film Cooling and Aerodynamic Performance of Squealer Blade Tip with Inclined Cavity Bottom