Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Printability Improvement of Rice Starch Gel Via Catechin and Procyanidin in Hot Extrusion 3D Printing

Enhancing 3D Printing Accuracy of Cassava Starch Gel Through Temperature-Controlled Freezing

Investigation of the 3D Printability of Modified Starch-Based Inks and Their Formation Mechanism: Application in Ice Cream

Effect of Pre-Printing Gelatinization Degree on the Structure and Digestibility of Hot-Extrusion 3D-Printed Starch

Insights into the Relationship Between Structure and Rheological Properties of Starch Gels in Hot-Extrusion 3D Printing

Effect of Rheological Properties of Potato, Rice and Corn Starches on Their Hot-Extrusion 3D Printing Behaviors

Effect of Starch Molecular Structure on Precision and Texture Properties of 3D Printed Products

Pre-dry heat treatment alters the structure and ultimate in vitro digestibility of wheat starch-lipids complex in hot-extrusion 3D printing

Starch Concentration is an Important Factor for Controlling Its Digestibility During Hot-Extrusion 3D Printing

Effect of Starch-Catechin Interaction on Regulation of Starch Digestibility During Hot-Extrusion 3D Printing: Structural Analysis and Simulation Study

Research on rice starch gel preparation and crosslink network structure-rheological property based on direct-writing 3D printing

3D Extrusion Printability of Rice Starch and Optimization of Process Variables

Modified Starch-Based Emulsion-Filled Gels for 3D Printing: Preparation, Characterization, and Printability

Understanding the structure and rheological properties of potato starch induced by hot-extrusion 3D printing

Impact of starch amylose and amylopectin on the rheological and 3D printing properties of corn starch

Effect of ferulic acid incorporation on structural, rheological, and digestive properties of hot-extrusion 3D-printed rice starch

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

Control of Starch-Lipid Interactions on Starch Digestibility During Hot-Extrusion 3D Printing for Starchy Foods

Investigation of the mechanism of different 3D printing performance of starch and whole flour gels from tuber crops

Effect of Stearic Acid on the Microstructural, Rheological and 3D Printing Characteristics of Rice Starch.

Hot extrusion 3D printing technologies based on starchy food: A review