Abstract:Abstract The coarse β -grain structures typically found in titanium alloys like Ti–6Al–4V (wt pct, Ti64) and Ti–6Al–2Sn–4Zr–2Mo–0.1Si (Ti6242), produced by high deposition rate additive manufacturing (AM) processes, are detrimental to mechanical performance. Certain modified processing conditions have been shown to lead to a more refined grain structure, which has generally been attributed to a change in the solidification conditions with respect to the experimental Hunt diagram proposed by Semiatin and Kobryn. It is shown that with Wire Arc AM (WAAM) increasing the wire feed speed (WFS) is effective in promoting a columnar-equiaxed transition (CET). Conversely, estimates of the dendrite-tip undercooling using the KGT model suggest that this will be too small for free nucleation without the addition of artificial nucleants, due to the very low solute partitioning in Ti alloys. It is also shown that it is difficult to promote a CET with plasma transferred arc WAAM as computational fluid dynamics (CFD) melt-pool simulations indicate that the solidification parameters remain within the columnar region on the Semiatin-Kobryn Hunt map, within the constraints of a stable process. However, a high fraction of twin boundaries was observed in the refined β -grain structures seen at high WFS. This has been attributed to departure of $$\left\langle {001} \right\rangle _{\beta }$$ 001 β alignment from the direction of maximum thermal gradient, caused by the curvature of the fusion boundary, stimulating dendrite twinning during solidification. In addition, it is shown that increasing the WFS leads to a change in melt-pool geometry and a reduction of remelt depth, which promoted dendrite twinning and grain refinement.

Grain Morphology Evolution Mechanism of Titanium Alloy by the Combination of Pulsed Arc and Solution Element During Wire Arc Additive Manufacturing

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy

Understanding the grain refinement mechanisms in aluminium 2319 alloy produced by wire arc additive manufacturing

Promoting the columnar to equiaxed transition and grain refinement of titanium alloys during additive manufacturing

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Achieving a Columnar-to-Equiaxed Transition Through Dendrite Twinning in High Deposition Rate Additively Manufactured Titanium Alloys

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

Simulation of solidified <i></i> grain for Ti-6Al-4V during wire laser additive manufacturing by three-dimensional cellular automaton method

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Microstructure regulation of titanium alloy functionally gradient materials fabricated by alternating current assisted wire arc additive manufacturing

Mathematical analysis and process optimization of wire and arc additive manufactured Ti6Al4V ELI alloy with in-situ rolling

Grain Selection and Growth Orientation of Prior-Β Phase for Ti-6-4 During Additive Manufacturing: Insights from a Modeling Perspective

Controlling the Microstructure and Properties of Ti-6.5al-2zr-1mo-1v Components Fabricated by High-Deposition-Rate Wire Arc Additive Manufacturing

Weakening the Anisotropic Property and Refining Prior-β Grains via Hammer Peening Treatment During Wire Arc Additively Manufacturing of Ti-6Al-4V

Microstructural and Defect Evolution during WAAM Resulting in Mechanical Property Differences for AA5356 Component

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

Simulation of solidified β grain for Ti–6Al–4V during wire laser additive manufacturing by three-dimensional cellular automaton method

Modelling and Experimental Observation of the Deposition Geometry and Microstructure Evolution of Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Influencing mechanisms of melt behavior on metal vapor characteristic and columnar grain formation in wire-arc directed energy deposition of titanium alloy

Microstructural development during wire arc additive manufacturing of copper-based components