Abstract:Suction anchors subjected to inclined loads at the optimal load attachment point are an important taut mooring foundation of deepwater floating production and storage facilities. Sediments in the deepwater areas are generally soft clay with high water contents. It is important for designers to understand failure modes and bearing capacities of suction anchors with taut mooring system in soft clay. Geometry characteristic parameters of anchors, shear strengths of strata and loading cases may be main factors affecting failure modes and bearing capacities of suction anchors. In order to better understand variations of failure modes and bearing capacities resulting from variations of various affecting factors, model tests were conducted under 1g condition for suction anchors with taut mooring system in soft clays. Effects of the friction resistance of the outside wall, geometric characteristic parameters, the variation of soil shear strength along the depth, the loading direction and cyclic loads on the failure mode and the bearing capacity of suction anchors with taut system were studied. Following conclusions were obtained based on model test results. There are three typical failure modes for suction anchors subjected to the inclined load at the optimal load attachment point: (1) the anchor failure is the vertical pullout mode if the vertical ultimate resistance of an anchor is less than the lateral ultimate resistance; (2) the anchor failure is the mode of lateral squeezing strata if the vertical ultimate resistance of an anchor is larger than the lateral ultimate resistance; (3) the anchor failure is the mode of squeezing strata along the inclined upward direction if the lateral ultimate resistance of an anchor is close to the vertical ultimate resistance. For specified stratum, the loading direction and the load case, the failure mode can be changed to increase the bearing capacity of an anchor by optimizing geometric parameters of an anchor. If the lateral ultimate resistance of an anchor is less than the vertical ultimate resistance, the bearing capacity of the anchor does not increase with the increase of the vertical ultimate resistance. The failure of anchors is always the vertical pullout mode if the vertical ultimate resistance of an anchor is less than the lateral ultimate resistance when the loading direction angle from the horizontal decreases from 40 degree to 20 degree for suction anchors with taut mooring system. The cyclic load is an important factor affecting the failure mode and the bearing capacity. The degradation of the vertical ultimate resistance is larger than the degradation of the lateral ultimate resistance under cyclic loads. The failure of an anchor is still the vertical pullout mode under combined static and cyclic loads if the failure of an anchor is the vertical pullout mode under static loads. If the failure of an anchor is lateral failure mode strata under static loads, the failure mode of the anchor will depend on the cyclic degradation of the vertical ultimate resistance under combined static and cyclic loads. When model test results were predicted using the limiting equilibrium analysis method, predicted bearing capacities were basically in agreement with model test results and predicted failure modes were only in qualitative agreement with test results. Copyright © 2012 by the International Society of Offshore and Polar Engineers (ISOPE).

Principles And Error Analysis Of The Lift-Off Test To Evaluate The Prestressed Anchor Tendon'S Working Stress

Working Stress Measurement of Prestressed Anchor Cables:Detection Mechanism and Experimental Study of Lift-off Test

Behaviour and in Situ Tests of Self-Drilling Prestressed Anchors

A modified lift-off test for restressing anchors of a rehabilitated landslide slope

Analysis of shear characteristics of prestressed anchor cable and shear resistance of anchor joint plane

An Electromechanical Impedance-Based Method for Tensile Force Estimation and Damage Diagnosis of Post-Tensioning Systems

Systematic Monitoring of the Performance of Anchor Systems in Fractured Rock Masses

Analytic Method of Load-Displacement Curve for Tension Anchors Based on Hyperbolic Load-Transfer Function

Investigation into the time-dependent mechanical behavior of pre-stressed anchor bolts and fractured rock specimens under synchronized tensile loads

Experimental Study on Anchorage Mechanical Behavior and Surface Cracking Characteristics of a Non-persistent Jointed Rock Mass

Study on Mechanical Characteristics of Rock Type I Fracture and Anchorage Strengthening Mechanism

Study on Mechanical Response Characteristics of Anchor under Dynamic Disturbance

Techniques of Reverse Drawing Detection for of Prestress under Anchor

Coupling Effect of Creep Deformation and Prestress Loss of Anchored Jointed Rock

Numerical Simulation Analysis on Bearing Capacity Characteristics of Prestressed Anchor

Shear behavior of anchor blocks in externally prestressed concrete bridges

Study on the Performance of Full-Length Pre-Stressed Anchor Bolts

Monitoring and correction of the stress in an anchor bolt based on Pulse Pre‐Pumped Brillouin Optical Time Domain Analysis

The Comparative Analysis on Error of Theoretical Value in Tension State and Measured Value of Compression Dispersion-Type Anchor Cable in a Certain Project

Experimental investigation and damage evaluation of a novel bond type anchorage for carbon fiber reinforced polymer tendons

Model tests on failure modes and bearing capacities of suction anchors with taut mooring system