Abstract:This paper investigates the internal flow characteristics of an aggressive S-shaped air bleeding manifold under typical working condition with the throttle cone opening degree of 15% and the inlet Mach number of 0.34 by experimental and numerical simulation methods. Based on the experimental results of total pressure recovery coefficient, the realizable kε model was selected as a suitable turbulence model for the air bleeding manifold numerical simulation by analyzing the numerical results of different turbulence models. The numerical simulation results show that the flow separation occurs at the upper wall and lower wall near the first bend, which also leads to the vortex pair and causes the nonuniformity of the flow field in the exit. The curvature of the end walls and the cross-sectional area variation of air bleeding manifold have greatly influence on the flow structure. The severe deflectionon the lower wall of the first bend is the main factor causing the flow separation and total pressure loss. The mass-averaged total pressure recovery coefficient in exit is 0.9818, and the synthesis distortion index DC(60) in the exit is 0.1334.. INTRODUCTION Air bleeding manifold is an important component in the active clearance control system of high-pressure turbine. The study of the internal characteristic and the loss mechanism will provide theoretical basis for optimal design of the air bleeding manifold. In this paper, the air bleeding manifold is an aggressive S-shaped duct with variable geometric crosssection. The study on flow characteristics of S-shaped duct in aero-engine is focused on compressor and turbine intermediate duct [1-3], inlet [4-5] and nozzle [6]. It is very famous that AIDA-Aggressive Intermediate Duct Aerodynamics project within the 6th framework program funded by the European Commission two projects dealing exclusively or partly with the topic of intermediate ducts. The outcomes of the AIDA project gives turbine and compressor engineers access to a whole new class of validated “aggressive” duct designs and design tools that will allow a much better optimization of the whole compression and turbine system [7] . The pressure distribution in an S-shaped diffuser depends not only on the area change such as in straight-walled channels, but also upon the curvature of the end walls and hence of the streamlines. S-shaped diffuser has a major effect on the boundary layer behavior at the end walls, which is most critical due to the strongest adverse pressure gradients right after strong wall curvatures [7]. This feature makes the numerical simulation and testing of an aggressive S-shaped diffuser difficult. Wellborn et al. [8] observed the intense mixture of the boundary layer and the core flow in the wind tunnel experiment with the inlet Mach number of 0.6. The counter-rotating vortices convected low momentum fluid of the boundary layer toward the center of the duct, and a large region of streamwise flow separation occurred within the duct. A large number of experimental studies have been carried out on the flow characteristics of S-shaped duct [9-13]. About the numerical simulation study, many researchers have done lots of work to find more accurate turbulence models for numerical simulation [14-18]. Waston et al. [18] calculated the NASA 30/30 geometric model using RANS (S-A, k-ε and SST k-ω model) and zonal large eddy simulation (RANS/LES) approaches. It was found that LES could more reliably predict large degrees of separation, but the mesh requirements and consequent cost render the technique prohibitively expensive for the near future, certainly unacceptably so for routine calculations as part of an ongoing design process. Asghar et al.[19-20] explored the flow characteristics of a baseline Sshaped diffuser using experiment and numerical simulation methods. They concluded that the presence of streamwise and circumferential pressure gradients led to the 3-D flow and the flow distortion in the exit. In addition, different geometry parameters of the S-shaped diffuser would have greatly influence on the flow characteristics. In this paper, the internal flow characteristics of an aggressive S-shaped air bleeding manifold of high-pressure turbine with active clearance

A Study Of The Fluid Flow Through The Rectangular Tapered Tube Distributor Based On Cfd

Study on Flow Field in Capacity Regulating Actuator for Reciprocating Compressor

Application of CFD Simulation for Optimisation of the Multi-Pipe Gas Distributors in a Large-Scale Shallow Bubble Column

Influence of Short-Draft Tube on Fluid Dynamics in Bubble Column with CFD

Numerical simulation of cylinder orientation through a rotating straight expansion duct

Numerical Analysis on the Effect of Bifurcation Angle and Inlet Velocity on the Distribution Uniformity Performance of Consecutive Bifurcating Fluid Flow Distributors

Experimental study and numerical simulation of a venturi distributor

Numerical Investigation of Constructal Distributors with Different Configurations

3-D Steady CFD Analysis of Francis Turbine's Distributor

Experimental and Cfd Investigation of R410a Distributors for Air Conditioner

Measurement And Analysis On The Velocity Field Of Tubular Pump Unit Flow Passage

Experimental and Numerical Investigations of the Double-Barrel Distributor for Air Conditioner

Flow characteristics in the air bleeding manifold

Innovative simplified approach and numerical investigation for flow and heat transfer in internally threaded tubes

CFD and Experimental Analyses of Flow Distribution Uniformity in Minichannel Reactors with a Bifurcation Structure Manifold

Design Method and Application Effects of Embedded-Clapboard Distributor on Refrigerant Distribution among Multi-Tubes of Micro-Channel Heat Exchangers

Optimal designs for flow uniformity at inlet of microchannel flat tube heat exchanger

The Influence of Inlet Diameter and Average Hole Diameter of One Side Liquid Distributor on the Performance of Liquid Distribution

Researches on the Numerical Simulation and Improved Design of Gas Distributors

Experimental Investigation of the Flow Distribution of a 2-Dimensional Constructal Distributor

Improvements on Maldistribution of a High Temperature Multi-Channel Compact Heat Exchanger by Different Inlet Baffles