Abstract:Many Ti-base products are made of sheets/plates processed by rolling and strong crystallographic textures are often developed, especially for those with α-Ti as the major phase. Compared to intensive explorations of deformation behaviors of low alloyed Ti (including commercial-purity Ti) during rolling, much less has been made for high-purity Ti (HP-Ti), in spite of acknowledged important effects of some impurities on deformation modes of α-Ti. To clearly reveal microstructural, textural and hardness evolution of HP-Ti during rolling from low to medium strains, a typical HP-Ti sheet after 10–50% cold rolling was subjected to quantitative characterization by jointly using electron backscatter diffraction, electron channel contrast imaging, X-ray diffraction and hardness test. Results show that plastic deformation readily occurs through the active operation of both slip and twinning (mainly { 11 2 ¯ 2 } < 11 2 ¯ 3 ¯ > and { 10 1 ¯ 2 } < 10 1 ¯ 1 ¯ > ) during 10–30% rolling. As a result of massive twinning, initial grain structures are markedly refined along with significant grain reorientation, leading to largely reduced textural intensity and the presence of new components. At higher strains (>30%), slip becomes the only deformation mode with new twins no longer appearing. In the 50%-rolled specimen, a bimodal basal texture similar to the initial one is formed along with a weak component of c//TD. The HP-Ti sheet is always hardened with increasing strains (from 120.8 ± 5.7 HV to 234.3 ± 5.8 HV). Quantitative analyses reveal that the grain refinement caused by dense twins at low strain (10% rolling) can lead to significant hardening contribution, which keeps relatively stable during subsequent rolling. Since slip can play a more important role with increasing strains, denser low angle boundaries are produced and gradually make larger contributions to hardening. As the rolling reduction increases to 50%, the contribution from low angle grain boundaries to hardness exceeds that from high angle grain boundaries (Hall-Petch hardening). The results documented in this work should not only be able to help clarify specific deformation mechanisms of HP-Ti, but also provide important implications for improving their properties.

Impact of Non-Isothermal Warm Rolling on Microstructure, Texture and Mechanical Properties

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Analysis of Microstructure, Texture Evolution, and the Mechanism of Grain Refinement of Commercially Pure Titanium During Cold Rolling: Experiment and Simulation

Influence of Cold Rolling Reduction on the Deformation Behaviour and Crystallographic Orientation Development

Dependency Of Rolling Texture And Microstructure On Twinning And Recrystallization Behavior Of Cp-Ti Sheet

Quantitative study of microstructural, textural and hardness evolution of high-purity Ti sheet during rolling from low to medium strains

Effect of rolling path on microstructure and mechanical properties of Ti-6242 alloy

Microstructure and Textural Evolution During Cold Rolling and Annealing of Commercially Pure Titanium Sheet

Dynamic Precipitation and Recrystallization in Al-12.5 Wt%si-0.6 Wt%mg-0.1 Wt%ti Alloy During Hot-Rolling and Their Impacts on Mechanical Properties

Effect of rolling geometry on the mechanical properties, microstructure and recrystallization texture of Al-Mg-Si alloys

Effect of Warm Deformation on Precipitation and Mechanical Properties of a Cryorolled Al-Zn-Mg-Cu Sheet

Strengthening of CP-Ti by Rolling at Room Temperature

Effects of Pack Rolling Temperature on Microstructure and Mechanical Properties of Powder Metallurgical Ti-45Al-7Nb-0.3W Alloy

Experiments and Crystal Plasticity Finite Element Simulations of Texture Development during Cold Rolling in a Ti-15V-3Cr-3Sn-3Al Alloy

Hot and Cold Rolling of a Novel Near-Α Titanium Alloy: Mechanical Properties and Underlying Deformation Mechanism

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Effect of Pre-Annealing Deformation on the Recrystallized Texture and Grain Boundary Misorientation in Commercial Pure Titanium

Influence of cold rolling process on microstructure and mechanical properties of Cu-1.5%Ti alloy